Chapter 2: Installation
2-35
LAN1/2
SUPER X7DWA-N
Fan1
8-pin PWR
FP Control
SPK
PW LED
JOH1
Fan3
IDE1
Floppy
Fan4
SATA3
SATA5
USB4/5
PCI-X 133/100 MHz
PCI-X 133/100 MHz
Battery
GLAN
CTLR
JPL1
PCI-Exp x16
North Bridge
COM1
Fan6
Fan5
ATX PWR
4-Pin PWR
J3P
24-Pin
CPU1
CPU2
South Bridge
Fan7
PSF
Fan2
JIDE1
JIDE2
Compact Flash
LE1
Fan8
JCF1
JWF1
SATA2
SATA4
SATA1
SATA0
Slot1
Slot2
Slot3
PCI 33 MHz
Slot4
Slot5
PCI-33MHz
Slot6
PCI-Exp x16
IPMI
Slot7
DIMM 1A (Bank 1)
DIMM 1B (Bank 1)
DIMM 2A (Bank 2)
DIMM 2B (Bank 2)
DIMM 3A (Bank 3)
DIMM 3B (Bank 3)
DIMM 4A (Bank 4)
DIMM 4B (Bank 4)
JBT1
JWOL
JWOR
JCOM2
KB/
Mouse
USB 0/
1/2/3
JI
2
C2
BIOS
CPU
Fan 1
FP Audio
CD1
JI
2
C1
CPU
Fan2
HD
Audio
SGPIO1
SGPIO2
Parrallel
Port
Clear
CMOS
Cha. Intru.
4-Pin
PWR
JI
2
C4
JI
2
C3
Slot0
PCI-U
IPMB
1394-1
1394-2
ESB2
Buzzer
JAR
S I/O
1394
CTLR
®
JWD
SMB_PS
IDE Drive Connectors
Pin Defi nitions
Pin# Defi nition Pin # Defi nition
1 Reset IDE 2 Ground
3 Host Data 7 4 Host Data 8
5 Host Data 6 6 Host Data 9
7 Host Data 5 8 Host Data 10
9 Host Data 4 10 Host Data 11
11 Host Data 3 12 Host Data 12
13 Host Data 2 14 Host Data 13
15 Host Data 1 16 Host Data 14
17 Host Data 0 18 Host Data 15
19 Ground 20 Key
21 DRQ3 22 Ground
23 I/O Write 24 Ground
25 I/O Read 26 Ground
27 IOCHRDY 28 BALE
29 DACK3 30 Ground
31 IRQ14 32 IOCS16
33 Addr1 34 Ground
35 Addr0 36 Addr2
37 Chip Select 0 38 Chip Select 1
39 Activity 40 Ground
A
B
C
A. IDE#1
B. IDE#2 (Compact Flash)
IDE Connectors
There are two IDE Connectors
(JIDE1: Blue, JIDE2: White) on
the motherboard. The blue IDE
connector (JIDE1) is designated
the Primary IDE Drive. The white
IDE connector (JIDE2) is desig-
nated the Secondary IDE Drive,
reserved for Compact Flash Card
use only. (See the Note below.)
See the table on the right for pin
defi nitions.
Note: JIDE2 (the white slot) is
reserved for Compact Flash Card
only. Do not use it for other de-
vices. If JIDE2 is populated with
a Compact Flash Card, JIDE1
(the blue slot) will be available for
one device only. For the Compact
Flash Card to work properly, you
will need to connect a power cable
to JWF1 fi rst.
To Next Page
Loading...
