Supermicro X9QR7-TF+ - Overheat Led;Fan Fail; DOM Power Connector

2-30
X9QR7-TF+/X9QRi-F+ Motherboard User’s Manual
JPW1
JPI2C1
JP5
JP4
USB6/7
JLPC1
JD1
JF1
JPW5
JPW4
JPW3
JPW2
JS2
JS1
A
UFBMC1
USB4
COM2
FAN9
JPS1
JPB1
JPG1
JPME1
JPT1
JWP1
J3
J2
JOH1
JPRST1
JPME2
JL1
SWUID1
SAS CTRL
LEDUID1
I-SATA0
I-SATA1
I-SATA5
I-SATA4
I-SATA3
I-SATA2
CPU1 SLOT4 PCI-E 3.0 X16
CPU1 SLOT3 PCI-E 3.0 X8 IN X16
CPU4 SLOT2 PCI-E 3.0 X16
CPU4 SLOT1 PCI-E 3.0 X8 IN X16
FAN1
FAN2
FAN3
FAN5
FAN6
FAN7
FAN10
FAN8
IPMI_LAN
COM1
USB0/1
USB2/3
LAN1
LAN2
VGA
P4 DIMMR1
P4 DIMMR2
P4 DIMMT1
P4 DIMMT2
P4 DIMMP2
P4 DIMMP1
P4 DIMMN2
P4 DIMMN1
P3 DIMMK1
P3 DIMMJ2
P3 DIMMJ1
P3 DIMMM2
P3 DIMML1
P3 DIMML2
P3 DIMMM1
P2 DIMME1
P2 DIMME2
P2 DIMMF1
P2 DIMMG2
P2 DIMMG1
P2 DIMMH2 P2 DIMMH1
P1 DIMMD2
P1 DIMMD1
P1 DIMMC2
P1 DIMMC1
P1 DIMMB2
P1 DIMMB1
P1 DIMMA1
P1 DIMMA2
CPU2
CPU1
CPU4
CPU3
USB5
JSD1
JPTG1
P3 DIMMK2
JIPMB1
P2 DIMMF2
J3J6
LAN CTRL
BMC CTRL
PCH
LS2E1
BIOS
DS1
CLPD
BMC FW
CPU1
X9QR7-TF+/X9QRi-F+
Rev. 1.02A
A
CPU1
A
CPU1
A
CPU1
FAN4
JWD1
BT1H1
T-SGPIO1
T-SGPIO2
JBT1
SAS_0~3
SAS_4~7
A
B
A. JOH1
B. DOM PWR
Overheat LED/Fan Fail
The JOH1 header is used to connect
an LED indicator to provide warnings
of chassis overheating and fan failure.
This LED will blink when a fan failure
occurs. Refer to the tables on right for
pin denitions.
Overheat LED
Pin Denitions
Pin# Denition
1 5vDC
2 OH Active
OH/Fan Fail LED
Status
State Message
Solid Overheat
Blinking Fan Fail
DOM Power Connector
A power connector for SATA DOM
(Disk_On_Module) devices is located
at JSD1. Connect an appropriate
cable here to provide power support
for your DOM devices.
DOM PWR
Pin Denitions
Pin# Denition
1 +5V
2 Ground
3 Ground