Supermicro X9QR7-TF+ - Jumper Settings; Explanation of Jumpers; LAN Ports Enable;Disable

Chapter 2: Installation
2-33
JPW1
JPI2C1
JP5
JP4
USB6/7
JLPC1
JD1
JF1
JPW5
JPW4
JPW3
JPW2
JS2
JS1
A
UFBMC1
USB4
COM2
FAN9
JPS1
JPB1
JPG1
JPME1
JPT1
JWP1
J3
J2
JOH1
JPRST1
JPME2
JL1
SWUID1
SAS CTRL
LEDUID1
I-SATA0
I-SATA1
I-SATA5
I-SATA4
I-SATA3
I-SATA2
CPU1 SLOT4 PCI-E 3.0 X16
CPU1 SLOT3 PCI-E 3.0 X8 IN X16
CPU4 SLOT2 PCI-E 3.0 X16
CPU4 SLOT1 PCI-E 3.0 X8 IN X16
FAN1
FAN2
FAN3
FAN5
FAN6
FAN7
FAN10
FAN8
IPMI_LAN
COM1
USB0/1
USB2/3
LAN1
LAN2
VGA
P4 DIMMR1
P4 DIMMR2
P4 DIMMT1
P4 DIMMT2
P4 DIMMP2
P4 DIMMP1
P4 DIMMN2
P4 DIMMN1
P3 DIMMK1
P3 DIMMJ2
P3 DIMMJ1
P3 DIMMM2
P3 DIMML1
P3 DIMML2
P3 DIMMM1
P2 DIMME1
P2 DIMME2
P2 DIMMF1
P2 DIMMG2
P2 DIMMG1
P2 DIMMH2 P2 DIMMH1
P1 DIMMD2
P1 DIMMD1
P1 DIMMC2
P1 DIMMC1
P1 DIMMB2
P1 DIMMB1
P1 DIMMA1
P1 DIMMA2
CPU2
CPU1
CPU4
CPU3
USB5
JSD1
JPTG1
P3 DIMMK2
JIPMB1
P2 DIMMF2
J3J6
LAN CTRL
BMC CTRL
PCH
LS2E1
BIOS
DS1
CLPD
BMC FW
CPU1
X9QR7-TF+/X9QRi-F+
Rev. 1.02A
A
CPU1
A
CPU1
A
CPU1
FAN4
JWD1
BT1H1
T-SGPIO1
T-SGPIO2
JBT1
SAS_0~3
SAS_4~7
2-8 Jumper Settings
Explanation of Jumpers
To modify the operation of the mother-
board, jumpers can be used to choose
between optional settings. Jumpers create
shorts between two pins to change the
function of the connector. Pin 1 is identied
with a square solder pad on the printed
circuit board. See the motherboard layout
pages for jumper locations.
Note: On two pin jumpers,
"Closed" means the jumper is
on and "Open" means the jumper
is off the pins.
Connector
Pins
Jumper
Cap
Setting
Pin 1-2 short
3 2 1
3 2 1
LAN Ports Enable/Disable
JPTG1 enables or disables the LAN
Port1/LAN Port2 on the motherboard. See
the table on the right for jumper settings.
The default setting is Enabled.
LAN Enable
Jumper Settings
Jumper Setting Denition
1-2 Enabled (default)
2-3 Disabled
A
A. LAN Ports Enable