SYSMEX KX-21 - Page 304

Sysmex KX-21 Operator’s Manual -- Revised October 1998 i
INDEX
0.5 kg/cm2 Pressure Error --------------------7-7
0.5 kg/cm2 Pressure Error at count ----------7-9
250 mmHg Vacuum Error--------------------7-8
A
Abnormal Detection Sensitivity-------------7-22
Adjusting Pressure to 0.5 kg/cm
2
-------------8-5
Adjusting Vacuum to 250 mmHg------------8-6
Alarm Sounds --------------------------------1-11
Analysis Error--------------------------------7-21
Analysis for Automatic Calibration ----------6-6
Analysis of Histogram-----------------------9-11
Analysis of RBC/PLT Histogram -----------9-20
Analysis of WBC Histogram ----------------9-11
Analysis Parameters----------------------------1-4
Analysis Procedure Flow Chart ---------------2-2
Analyzing Samples (in PD Mode)----------2-21
Analyzing Samples (in WB Mode) --------- 2-12
As-Needed Maintenance and Procedure--- 4-24
Auto Rinse------------------------------------4-24
Automatic Calibration -------------------------6-3
Automatic Calibration Procedure-------------6-4
Automatic Stop Function of Pneumatic Unit1-3
B
Background Error ---------------------------7-17
Bellows Unit -----------------------------8-6, 9-33
Blood Cell Discrimination Circuit ---------- 9-10
C
Calculating Calibration Value-----------------6-9
Calculation of RBC Constant------------------9-9
Calibration Error-----------------------------7-26
Calibration Execution Timing ----------------6-1
Calibration Flow Chart-------------------------6-2
CBC Analysis-----------------------------------9-5
Cell-Count Parameters-----------------------2-26
Check before Installation---------------------A-2
Check Trap Chamber Level and Discard ----4-6
Clean Rinse Cup------------------------------4-26
Clean Sample Rotor Valve (SRV) ----------4-16
Clean SRV Tray--------------------------------4-7
Clean TD Chamber and Diluted Sample Line
(Shutdown)------------------------------4-4
Clean Transducer (Rinse Sequence)--------4-12
Clean Waste Chamber (Rinse Sequence)-----4-9
Clean WBC/RBC Transducer Aperture -----4-28
Clog in the aperture--------------------------7-15
Correcting a Sample Number---------------3-17
Collecting and Preparing Samples-----2-9, 2-16
Confirmation of Cycle Number ------------4-41
Connect CELLPACK -------------------------A-6
Connect Power Cord-------------------------A-12
Connect STROMATOLYSER-WH ----------A-8
Connect Tube --------------------------------- A-6
Connect Waste Line---------------------------A-9
Contents of Display----------------------------1-7
Contents of Package -------------------------1-11
D
Daily Maintenance and Procedure -----------4-4
Date/Time Settings ---------------------------10-7
DC Detection Method -------------------------9-2
Deletion---------------------------------------5-25
Deletion (Stored Data)-----------------------3-15
Detection Principle-----------------------------9-2
Display and Printing of Analysis Result --- 2-24
Display of Analysis Result -------------2-24, 3-2
E
Electric Diagram -----------------------------9-29
Electric System-------------------------------9-28
Emergency Stop Procedure-----------------1-11
Entering Calibration Value------------------6-11
Entering Target Values------------------------6-5
Erase All ----------------------------------------5-6
Every 3-month Maintenance and
Procedure------------------------------4-16
Execute
X
Control-----------------------------5-9
Execute L-J Control -------------------------5-18
Execute QC Program --------------------------5-5
Executing and Quitting Stored Data
Processing Program-------------------3-11
Executing Automatic Calibration Program--6-3
Execution of Shutdown ---------------------2-30
Exit from QC Program ----------------------5-24
Expected Results -----------------------------2-28
F
Factory Settings -----------------------------10-27
Front Panel -----------------------------------9-30
Front Interior--------------------------------- 9-31
Functional List of Error Messages------------7-5
G
Graphic Screen---------------------------------1-7
Grounding------------------------------------1-12