What to do if the fixed position signal is not detected on my TAJIMA Sewing Machine?
If the fixed position signal (main shaft Z signal) is not detected, return the main shaft to the fixed position and check the encoder signal on your TAJIMA Sewing Machine.
Critical warnings and guidelines to ensure safe operation of the machine.
Highlights the primary capabilities and features of the embroidery machine.
Explains the layout and functions of the machine's control panel.
Illustrates where warning labels are placed on the TFHX and TEHX-C machines.
Describes the noise reduction features for a comfortable working environment.
Explains how the machine prevents data loss during power interruptions.
Details the function that automatically prevents skip stitches and thread breakage.
Lists parts of the TFHX model.
Lists parts of the TFHX-C model.
Lists parts of the TEHX-C model.
Lists the electrical specifications of the machine.
Describes the components and function of the power supply/driver box.
Details the purpose and operation of each part of the operation panel.
Details functions accessible via Menu Key A.
Details functions accessible via Menu Key B.
Details functions accessible via Menu Key C.
Details functions accessible via Menu Key D.
Explains the operation and function of the tension base switch.
Details the function and indication of the thread breakage lamp.
Details how to turn the machine's power on and off.
Explains how to use the emergency stop switch to halt the machine.
Details how to start and stop the machine using the bar switch on TFHX models.
Details how to start and stop the machine using the start/stop switch on non-TFHX models.
Explains how the machine stops automatically based on preset values.
Guidelines for handling and storing floppy disks to prevent damage.
Instructions for using and maintaining the floppy disk drive.
Details the steps for turning on the power and completing software installation.
Specific settings for TEHX-C models after software installation.
Specific settings for TFHX models after software installation.
Setting the number of needles and heads for TEHX-C.
Setting needles, machine type, and number of heads for TFHX models.
Shows the screen display after initial software self-check.
Describes the standard screen display after software check.
Shows the screen display during active embroidery operation.
Lists the settings required for design data input.
Shows the interface for setting design data input.
Lists the settings required for floppy disk data input.
Shows the interface for setting floppy disk data input.
Lists the settings required for external device data input.
Shows the interface for setting external device data input.
Lists the settings required for standby input.
Shows the interface for setting standby input.
Lists the settings for deleting design data.
Shows the interface for selecting memory deletion options.
Lists the parameters for editing stitch data.
Shows the interface for selecting design and stitch data for editing.
Lists the parameters for inserting stitch data.
Shows the interface for selecting design and stitch data for insertion.
Lists the parameters for deleting stitch data.
Shows the interface for selecting design and stitch data for deletion.
Lists the settings for cleaning stitch data.
Shows the interface for selecting design and stitch data for cleanup.
Lists the settings for writing design data to floppy disk.
Shows the interface for selecting design data for writing.
Lists the settings for deleting floppy disk data.
Shows the interface for selecting design data for deletion from floppy disk.
Lists the settings for floppy disk formatting.
Shows the interface for selecting floppy disk type for formatting.
Lists the settings for manual color change.
Shows the interface for selecting manual color change options.
Shows the interface for manual thread trimming.
Shows the interface for performing manual origin return.
Shows the interface for performing manual offset.
Shows the interface for selecting trace options.
Operation using the manual frame travel key.
Operation using the jog dial and jog shuttle.
Shows the interface for setting frame back/forward parameters.
Lists the settings for frame origin memory.
Shows the interface for setting frame origin memory.
Shows the interface for setting frame origin memory for TFHX/TEHX-C.
Lists the settings for power resume functionality.
Shows the interface for configuring power resume.
Lists the settings for power resume functionality.
Shows the interface for configuring power resume.
Shows the stitch counter and design time display.
Procedure for resetting the stitch counter.
Confirms settings related to data input.
Confirms settings related to needle bar selection.
Shows the number of stitches for automatic lubrication.
Lists the settings for manual lubrication.
Shows the interface for manual lubrication control.
Lists the settings for table up/down functionality.
Shows the interface for controlling table up/down.
Lists the settings for sequin device movement.
Shows the interface for controlling sequin device movement.
Lists the settings for maximum revolution.
Shows the interface for setting the maximum revolution.
Lists the settings for low speed revolutions.
Shows the interface for setting low speed revolutions.
Lists the settings for the limit of maximum revolution.
Shows the interface for setting the limit of maximum revolution.
Lists the settings for the number of inching times.
Shows the interface for setting the number of inching times.
Lists the settings for frame drive start timing.
Shows the interface for setting frame drive start timing.
Lists the settings for frame travel speed.
Shows the interface for setting frame travel speed.
Lists the settings for adjusting main shaft stop position.
Shows the interface for adjusting main shaft stop position.
Lists the settings for frame drive method.
Shows the interface for setting frame drive method.
Lists the settings for frame back/forward.
Shows the interface for setting frame back/forward.
Lists the settings for the table up/down device.
Shows the interface for enabling the table up/down device.
Sets detection times for all needle bars simultaneously.
Sets detection times for each needle bar individually.
Sets detection times for all needle bars simultaneously.
Sets detection times for each needle bar individually.
Sets movement ratio for all needle bars simultaneously.
Sets movement ratio for each needle bar individually.
Lists the parameters for automatic thread trimming.
Shows the interface for setting automatic thread trimming.
Lists the settings for auto color change and start.
Shows the interface for setting auto color change and start.
Lists the settings for needle bar selection.
Shows the interface for setting needle bar selection.
Lists the settings for repeating designs.
Shows the interface for setting repeat parameters.
Lists the settings for automatic offset.
Shows the interface for setting automatic offset.
Lists the settings for offsetting at automatic color change.
Shows the interface for setting offsetting at automatic color change.
Lists the settings for automatic start after data set.
Shows the interface for setting automatic start.
Lists the settings for automatic origin return.
Shows the interface for setting automatic origin return.
Lists the various preset halt methods and settings.
Shows the interface for configuring preset halt.
Lists the settings for stopping at the pseudo-fixed position.
Shows the interface for setting the pseudo-fixed stop position.
Lists the parameters for data conversion (size, rotation, reversion).
Shows the interface for setting data conversion parameters.
Lists the settings for jump conversion.
Shows the interface for setting jump conversion parameters.
Lists the settings for automatic jump.
Shows the interface for setting automatic jump stitch length.
Lists the settings for satin stitch length adjustment.
Shows the interface for adjusting satin stitch length.
Lists the settings for correcting backlash.
Shows the interface for setting backlash correction values.
Lists the settings for all-head sewing after frame back.
Shows the interface for setting all-head sewing parameters.
Lists the settings for the boring device.
Shows the interface for enabling and configuring the boring device.
Lists the settings for the cording device.
Shows the interface for enabling and configuring the cording device.
Lists the settings for network communication.
Shows the interface for enabling network communication.
Lists the settings for the sequin device and feed amount.
Shows the interface for configuring sequin device operation.
Lists the settings for the automatic lubrication system.
Shows the interface for configuring automatic lubrication.
Lists the settings for the bobbin changer.
Shows the interface for enabling and configuring the bobbin changer.
Adjusts the size of the design in X and Y directions.
Rotates the design by a specified angle.
Reverses the design horizontally or vertically.
Indicates the starting point for repeated designs.
Sets the spacing between repeats in the X direction.
Sets the spacing between repeats in the Y direction.
Returns the frame to the original position after manual travel.
Automatically moves the frame forward after embroidery completion.
Covers frame travel methods like batch processing and as-data for jump conversion.
Corrects mechanical errors in X/Y-axis drive systems.
Moves the frame along the design path for checking.
Reduces or enlarges the satin stitch length.
Lists common error codes and their corrective actions.
Details errors indicated by code numbers and their solutions.
Explains non-error related stops and their resolutions.
Lists common symptoms, causes, and corrective actions for machine issues.
Procedure to disable a faulty head to allow operation with remaining heads.
Details the cleaning procedures and cycles for machine parts.
Provides lubrication points and cycles for the TFHX series.
Provides lubrication points and cycles for the TEHX-C series.
Details greasing spots and cycles for the TFHX series.
Details greasing spots and cycles for the TEHX-C series.
Outlines regular inspections for machine parts like belts.
General guidelines and warnings for performing machine repairs.
A mechanical origin point for detecting the frame's absolute position.
Automatic Frame Changer: enables continuous automatic embroidery.
Automatic Thread Trimming and Holding Device.
A slide switch used to change machine movement conditions.
Frames that hold the material for embroidery.
Codes indicating the end or pause point of embroidery designs.
Abbreviation for Floppy Disk Drive.
The process of writing data to the machine's internal memory.
Setting the order of needle bars used in each color change step.
A free setting position for temporary frame waiting during offset setup.
The position where trace or frame forward started after data set.
Sequence of color changes for one design or advancing values.
Data for each stitch including X/Y, function code, and speed code.
Data indicating embroidery frame movement in the X direction.
Data indicating embroidery frame movement in the Y direction.
General| Brand | TAJIMA |
|---|---|
| Model | TFHX Series |
| Category | Sewing Machine |
| Language | English |
To Next Page
