CD player section
(Audio)
Number of channels: 2
Frequency response: 20 - 20,000 Hz ± 0.5 dB
Signal-to-noise ratio: 90 dB
Total harmonic distortion: 0.02% (1 kHz)
Wow and flutter:
Unmeasurable (quartz accuracy)
Channel separation: 75 dB
Pitch control: Approx. ±12 %
Output (RCA): 2 Vrms
Output (XLR): +20 dBu
Digital filter: 4-times oversampling
Analog filter: 3rd order
Cassette section
Track system: 4-track 2-channel stereo
Heads: Record/playback x 1 (rotary
reverse), erase x 1
Type of tape: Cassette tape C-60, C-90
Tape speed: 4.76 cm/sec.
Pitch control: Approx. ±12 %
Motor: DC servo motor x 1
Wow and flutter: 0.08% (W. RMS)
Frequency response (overall):
50 – 15,000 Hz ± 3 dB, metal
50 – 15,000 Hz ± 3 dB, chrome
50 – 14,000 Hz ± 3 dB, normal
Signal-to-noise ratio (overall):
69dB(DOLBYNRoff,3%THD level, weighted),
69 dB (DOLBY NR on, over 5 kHz)
Fast winding time: Approx. 120 sec. (with C-
60)
Specifications
The heads and tape path should be cleaned
and demagnetized periodically.
Cleaning tape path
O Apply head cleaning fluid* to a cotton
bud or soft cloth, and lightly rub the
heads, capstan and all metal parts in the
tape path.
O Also clean the pinch roller using rubber
cleaning fluid*.
* Both are available in TEAC Tape
Cleaning Kits HC-2 and RC-2 in the
U.S.A. or TZ-261 in other areas.
Maintenance
Demagnetizing heads
Be sure that the power is off, then demag-
netize the heads using a TEAC E-3 demag-
netizer. For details of its use, read its
instructions.
Pinch Roller
Capstan
Erase Head
Record/Play Head
Input (RCA):
–9 dBu (input impedance of 50 kohms)
Input (XLR):
+4 dBu (input impedance of 10 kohms)
Line output (RCA):
–4.5 dBu (output impedance of 400
ohms)
Line output (XLR):
+4 dBu (output impedance of 150 ohms)
Headphones: 5 mW/32 ohms
General
Power requirements:
120/230 V AC, 50–60 Hz
(U.S.A./Canada/General export model)
230 V AC, 50 Hz (Europe/U.K. model)
240 V AC, 50 Hz (Australia model)
Power consumption: 15 W
Dimensions (W x H x D):
483 x 138.5 x 270 mm (19" x 5-1/4" x
10-5/8")
Weight: 6.6 kg (14.1 lbs.)
Standard accessories:
Wireless remote control RC-A500,
Battery (SUM-3, "AA", "R6" type) x 2,
Rack mounting screw kit
O Improvements may result in specifi-
cation or feature changes without
notice.
O Photos and illustrations may differ
slightly from production models.
IMPORTANT (for U.K. Customers)
DO NOT cut off the mains plug from this
equipment. If the plug fitted is not suit-
able for the power points in your home
or the cable is too short to reach a
power point, then obtain an appropriate
safety approved extension lead or con-
sult your dealer.
If nonetheless the mains plug is cut of
f,
remove the fuse and dispose of the plug
immediately, to avoid a possible shock
hazard by inadvertent connection to the
mains supply.
If this product is not provided with a
mains plug, or one has to be fitted,
then
follow the instructions given below:
IMPORTANT. DO NOT make any con-
nection to the larger terminal which is
marked with the letter E or by the safety
earth symbol ç or coloured GREEN or
GREEN-and-YELLOW.
The wires in the mains lead on this prod-
uct are coloured in accordance with the
following code:
BLUE: NEUTRAL
BROWN: LIVE
As these colours may not correspond
with the coloured markings identifying
the terminals in your plug proceed as
follows:
The wire which is coloured BLUE must
be connected to the terminal which is
marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN
must be connected to the terminal
which is marked with the letter L or
coloured RED.
When r
eplacing the fuse only a correct-
ly rated approved type should be used
and be sur
e to re-fit the fuse cover.
IF IN DOUBT — CONSULT A COMPE-
TENT ELECTRICIAN.
To Next Page
Loading...
