Taski Diversey ergodisc HD - Accessories; Disposal; Malfunctions; Technical Data

25
I25 I24 I23 I22 I21 I20 I19 I18 I17 tr th sv sl ro pt pl nl it fr fi en el de cz cn
Service intervals
TASKI machines are built to the highest quality standards. This is supported by
internationally recognised quality control procedures. Electrical and mechanical
parts are subject to wear or aging if used for long periods of time.
Service centre
Should you contact us due to a malfunction or for placing an order, please
always state the type, description and the serial number of your machine.
You can find this information on the name plate of your machine, and the
address of your nearest TASKI partner can be found on the last page of this
manual.
Malfunctions
Transport
Ensure that the machine is firmly lashed down and secured in the transport
vehicle.
Disposal
When it has reached the end of its operational life, the machine and its
accessories must be disposed of according to the national regulations. Your
TASKI partner can support you with proper disposal upon notification.
Technical data
Accessories
Symbols:
 = after use,  = every week,  = every month
Activity  page
Check the motor ventilation for the collection of
dust and clean when necessary
t
23
Clean the brushes
t
24
Clean the pads and let them dry
t
24
Wipe down the machine with a damp cloth
t
24
• In order to maintain operational reliability and availability for use, the service
must be carried out after 250 working hours or at least once a year.
Under rough or extreme working conditions and/or insufficient maintenance,
shorter periods are necessary.
Malfunction Possible causes Troubleshooting page
Machine does not
work
Plug not plugged in to
the mains socket
• Connect the power
supply cord to the
mains socket.
Guide bar in upright
position
• Place the machine in
the working position
23
Safety switch defect
• Contact your service
partner
23
Machine cannot
be operated, but
the switch is on
The machine has
been overloaded,
causing the
overcurrent protection
to be tripped
• Wait a while, try again
(the protection switch
will automatically
reset)
Tool does not
rotate
Motor runs but not
the tool
• Brush coupling, motor
axle or gearbox
possibly defective.
• Contact your service
partner
Machine does not
reach rated
speed, motor
protection cuts in
Machine is
overloaded
• Check if you are using
the correct working
technique
23
Insufficient voltage,
power cord is too long
• Remove extention
• Check power supply
voltage
Machine runs
uneasy
Tool deformed or
damaged
• Replace pad
• Remove the tool (refer to page 24).
• Pull the height adjustment lever and fold the
guide bar towards the front.
• Let go of the height adjustment lever, the guide
bar will locate into place and stay at that angle.
• To lift the machine, hold the machine between the wheels and the brush
cover while the second person holds onto the machine handle or on each
side at the brush cover.
Caution:
The machine must always be carried by at least two persons!
Machine HD
type 43LSHD
Brush width 43 cm
Dimensions (L x W x H) 46x48x107 cm
Machine weight 54 kg
Additional weight 10 kg
Total weight (including additional weight) 64 kg
Rated voltage 220-240V ac
Rated power 1100 W
Frequency 50 Hz
Power supply cord length 15 m
Brush speed 150 min-1
Brush pressure 0.4 N/cm2
Assessed sound level LPA according to
ISO 11201
<70 dB(A)
The assessed effective acceleration value according
to ISO 5349-1
<2.5 m /s2
Splash water protection IPX4
Protection class I
Article HD
8504390 Water tank X
8504410 Driving disc 43cm X
8504750 Scrubbing brush 43 cm X
8504800 Scrubbing brush for washed concrete 43 cm X
8504780 Scrubbing brush abrasive 43 cm X
7518579 Extra weight 10 kg X