TTHHDDC C / / TTHHDDCCP P - - 99554 4 / / 99555 5 / / 99774 4 ((RReevv. . 0066//0033) ) SSaaffeettyy--55
WARNING:WARNING: Never leave the containerNever leave the container
handlihandling truck ng truck with a with a containcontainer er suspendsuspended.ed.
The load could inadvertently lower and causeThe load could inadvertently lower and cause
serious injury or death.serious injury or death.
WARNING:WARNING: Be exact in load placement.Be exact in load placement.
Make sure the load will not tilt, fall or slide outMake sure the load will not tilt, fall or slide out
of positof position when releasedion when released. . Personal inPersonal injury orjury or
equipmequipment damage ent damage can result can result from unstablefrom unstable
placement of loads.placement of loads.
WARNING:WARNING: Do not unlatch a containerDo not unlatch a container
until you, the until you, the operatoperatoror, , have have determdetermined that itined that it
is safe to do so. is safe to do so. Never unlNever unlatch a contatch a containerainer
that is not positioned securely; the containerthat is not positioned securely; the container
could shift or fall.could shift or fall.
WARNING:WARNING: Do not back away from aDo not back away from a
rack or stack with a container until it is clear ofrack or stack with a container until it is clear of
the containthe container below it. er below it. FailurFailure to do so, maye to do so, may
result in death or serious bodily injury andresult in death or serious bodily injury and
property damage caused by dropping a con-property damage caused by dropping a con-
tainer on the truck, a bystander or on thetainer on the truck, a bystander or on the
ground.ground.
Battery Safety:Battery Safety:
WARNING:WARNING: Lighted smoking materials,Lighted smoking materials,
flames, arcs, or sparks may result in batteryflames, arcs, or sparks may result in battery
explosion.explosion.
1. 1. Keep all meKeep all metal tooltal tools away frs away from battom battery terery termi-mi-
nals.nals.
2. 2. Batteries Batteries contain scontain sulfuric ulfuric acid wacid which which will burill burnn
skin on contact; wear rubber gloves and eyeskin on contact; wear rubber gloves and eye
protection when working with batteries.protection when working with batteries.
3. 3. FluFlush eyes or wsh eyes or wash skash skin witin with water anh water and seekd seek
medical attention immediately in case ofmedical attention immediately in case of
contact.contact.
4. 4. When When jumjump sp starttarting:ing:
a. a. Do not leDo not lean over the baan over the batterttery whiy while makle makinging
connection.connection.
b. b. FirsFirst, connect, connect the posit the positive (tive (+) ter+) terminal ofminal of
the booster battery to the positive (+)the booster battery to the positive (+)
termiterminal nal of of the the dischardischarged ged batterybattery..
c. c. ThenThen, connec, connect the negatt the negative (-ive (-) term) terminal ofinal of
the booster battery to the engine or bodythe booster battery to the engine or body
ground (-). ground (-). Never CrNever Cross Polarioss Polarity ofty of
Terminals.Terminals.
d. d. DiscDisconnect cablonnect cables in exes in exact revact reverse orerse orderder..
Lock-Out / Tag-Out ProcedureLock-Out / Tag-Out Procedure
Purpose.Purpose. This procedure establishes the mini-This procedure establishes the mini-
mum requirements for lock-out / tag-out of energymum requirements for lock-out / tag-out of energy
sources that csources that could cause injurould cause injury to personnel. y to personnel. AllAll
employees shall comply with the procedure.employees shall comply with the procedure.
Responsibility.Responsibility.The responsibility for seeing thatThe responsibility for seeing that
this procedure is followed is binding upon allthis procedure is followed is binding upon all
employeesemployees. . All employAll employees shall be instees shall be instructed inructed in
the safety significance of the lock-out / tag-outthe safety significance of the lock-out / tag-out
procedure by (procedure by (designated indidesignated individual)vidual). . Each newEach new
or transferred affected employee shall beor transferred affected employee shall be
instructed by (designated individuals) in the pur-instructed by (designated individuals) in the pur-
pose and use of the lock-out / tag-out procedure.pose and use of the lock-out / tag-out procedure.
Preparation for Lock-Out / Tag-Out.Preparation for Lock-Out / Tag-Out. Employees Employees
authorized to perform lockout / tagout shall be cer-authorized to perform lockout / tagout shall be cer-
tain as to which switch, valve, or other energy iso-tain as to which switch, valve, or other energy iso-
lating devices apply to the equipment beinglating devices apply to the equipment being
locklocked out / tagged out. ed out / tagged out. MorMore than one energye than one energy
source (electrical, mechanical, or others) may besource (electrical, mechanical, or others) may be
involved. involved. Any questionAny questionable identifable identification ofication of
sources shall be cleared by the employees withsources shall be cleared by the employees with
their supervtheir supervisors. isors. Before lock-Before lock-out / tag-out com-out / tag-out com-
mences, job authorization should be obtained.mences, job authorization should be obtained.
Sequence of Sequence of Lock-OuLock-Out t / / TTag-Out Procedurag-Out Proceduree
1. 1. NotiNotify all affy all affecfected emplted employeeoyees that a lock-s that a lock-out /out /
tag-out is required and the reason therefor.tag-out is required and the reason therefor.
2. 2. If the equiIf the equipmenpment is opert is operatiating, shut ing, shut it down byt down by
the normal stopping procedure.the normal stopping procedure.
3. 3. OperOperate the swiate the switch, vatch, valvelve, or other ener, or other energy iso-gy iso-
lating device so that the energy source(s)lating device so that the energy source(s)
(electr(electrical, mechanical, hydraulic, etc.) ical, mechanical, hydraulic, etc.) is is dis-dis-
connected or isolated from the equipment.connected or isolated from the equipment.
Stored energy, such as that in capacitors,Stored energy, such as that in capacitors,
springs, elevated crane members, rotating fly-springs, elevated crane members, rotating fly-
wheels, hydraulic systemswheels, hydraulic systems, , and and airair, , gas,gas,
steam, or water pressure, etc. must also besteam, or water pressure, etc. must also be
dissipated or restrained by methods such asdissipated or restrained by methods such as
grounding, repositioning, blocking, bleeding-grounding, repositioning, blocking, bleeding-
down, etc.down, etc.
4. 4. Lock-out Lock-out / tag-/ tag-out the out the energy ienergy isolating solating devicesdevices
with an assigned individual lock / tag.with an assigned individual lock / tag.
5. 5. After eAfter ensurnsuring that no pering that no personnesonnel are expl are exposedosed
and as a check on having disconnected theand as a check on having disconnected the
energy sources, operate the push button orenergy sources, operate the push button or
other normal operating controls to make cer-other normal operating controls to make cer-
tain the equipment will not operate.tain the equipment will not operate.
CAUTION:CAUTION: Return operating controls toReturn operating controls to
neutral after the test.neutral after the test.
To Next Page
Loading...
Need help?
General
