Teac TASCAM 32 - Page 5

energy
to
be
generated
by
the
micro-
phones.
This
ATT
button
affects
the
MIC
circuit
only.
@® VU Meters
OVU
=.3
Volt.
What
signal
will
be
shown
on
the
meters
will
depend
on
the
settings
of
the
OUTPUT
SELECT
buttons.
For
a
comprehen-
sive
list
of
the
possible
meter
logic,
see
item
24,
OUTPUT
SELECT
buttons.
@
FUNCTION
LED
Indicators
Indicates
which
FUNCTION
buttons
have
been
activated.
@
FUNCTION
(L,
R)
Buttons
Determines
the
record/reproduce
status
of
the
corresponding
channels.
Up
—
Safe,
reproduce
or
source
determined
by
OUTPUT
SELECT
buttons.
Down
—
Ready
to
record.
If
‘’Record’’
has
been
selected
through
the
transport
controls,
depressing
this
button
will
begin
re-
cording
immediately.
Output
of
re-
corder
switches
to
source.
@
INPUT
Level
Controls
For
adjusting
the
MIC
or
LINE
level
signal.
Setting
has
no
effect
on
reproduce.
This
control
is
of
a
dual
concentric
type,
so
either
channel
can
be
adjusted
independently.
®
OUTPUT
Level
Controls
For
adjusting
the
levels
of
the
signals
sent
to
the
OUTPUT
(L
&
R)
terminals.
This
control
is
of
a
dual
concentric
type,
so
either
channel
can
be
adjusted
independently.
Use
this
control
to
set
optimum
monitoring
or
listening
levels.
@
OUTPUT
SELECT
Buttons
Select
which
of
three
possible
sources
to
feed
the
output
jacks
(rear
panel)
and
VU
meter
circuits.
The
LED’s
above
the
buttons
show
selection.
INPUT
—
Meter
reads
line
input
to
recorder,
input
signal
appears
at
output
jacks.
Tape
signal
will
not
be
heard.
SYNC
-—
Used
for
all
normal
operations,
recording,
sync/reproduce
and
re-
produce.
Meter
reads
input
or
head
#2
play
output
depending
on
setting
of
function
buttons
(L
or/and
R).
REPRO
—
Selects
head
#3.
Meter
now
reads
tape
playback.
Does
not
prevent
recording
on
head
#2.
Used
in
to check performance and record/
play monitoring of tape.
@® OUTPUT SELECT LED Indicators
Indicates which OUTPUT SELECT buttons have
been activated.
INPUT LED : Red
SYNC LED: Yellow
REPRO LED: Green
@ Transport Controls
This group of buttons control the mechanical
action of the transport, and the in/out switching
of the record circuit. The RC-71 remote control
unit (see rear panel for the connection point)
will duplicate this control group. When the
remote is connected, both sets of controls will
be active at the same time.
{ >» ) Play Button
1. When depressed alone, the tape will advance
at the speed selected by the # 10 SPEED switch
and the #12 PITCH CONTROL.
2.When depressed along with the RECORD
button, any or all tracks that have their FUNC-
TION select buttons IN (record ready) will
begin recording immediately.
3. This transport has a motion sensing circuit
that aliows the selection of PLAY directly from
either fast forward or rewind. Press PLAY when
fast winding and the transport will slow, come
briefly to STOP and then enter PLAY by itself.
( >> ) Fast Forward Button
( «« ) Rewind Button
Rewind time is 90 seconds for a 10-1/2” reel,
1-1/2 mil tape.
STOP Button
RECORD Button
Depressing this button by itself will Mave no
effect. To begin recording, several conditions
must first be met.
1. One or more FUNCTION select buttons must
be IN (record ready)
2. To enable the record logic, the PLAY button
must be depressed simultaneously with the
RECORD button. If the transport is in PLAY,
press BOTH buttons together and the unit will
go into record mode.
3. Since the PAUSE button can hold the record
logic in an active condition (see next page,
PAUSE button) if PAUSE is active, recording
can start with a one button PLAY command.
4. Since depressing PLAY/RECORD wil enable
the record logic when the FUNCTION select
buttons are NOT active, it is possible to begin
recording with this sequence as well as te more
usual ones. Do this;