Teac X-2000R - Recording Performance

3-3
MONITOR
PERFORMANCE
EAIK
. Min. LINE
input level
LINES Js
ANLAIL
input level
MICS.
. Specified LINE
input level
LINE S852
. PHONES input
level
Ay FAR IIE
AC voltmeter to REC
and PLAY PCB TP.03/
TP.13 and GND.
LINE cont.: MAX
MIC cont.: MIN
Same as above [Fl_t.
Connection: Fig.
LINE cont.: MIN
MIC cont.: MAX
LINE cont.: MAX
MIC cont.: MIN
LINE IN:
400 Hz/—22 dB
(61.5 mV)
MIC:
400 Hz/—70 dB
{245 nV)
LINE IN:
400 Hz/—12 dB
(195 mv)
X-2000R
Deck settings
OUTPUT
cont.
Specified
playback
condition.
<#t72
4:
1kKRR>
MONITOR sw: SOURCE
TP.03/TP.13:
—2 dB (615 mV)
OUTPUT:
Check —5 dB +1 dB
FIVI (388 mV~489 mV)
OUTPUT:
Check —5 dB 43 dB
FID (308 mV~615 mV)
R557/R957
LINE cont OUTPUT R:
(L/R) —5 dB (436 mV)
OUTPUT L:
Check —5 dB +1 dB
FIYI (388mV~489mV)
LINE cont. OUTPUT L:
(L) —5 dB (436 mv)
LINE
specified
input
condition.
IMPORTANT:
Do
not
touch
LINE
cont.
during
later
checks,
TER
|
UMOMBICH
TLINEDEACMOSEVTC.
LINES A HARES
LINE spec. input
condition
LINESLE A AK
Same as above
Tat
LINE IN:
400 Hz/— 12 dB
(195 mV)
LINE IN:
400 Hz/—12 dB
(195 mV)
R558/R958 VU meter: 0 VU
PHONES jack:
patna 8.8 dB 42 dB
amc (224 mV~354mV)
3-4 RECORDING PERFORMANCE
RBH
Deck settings
REC MODEsw: L&R both ON
DBXsw:
OUT
OUTPUT
cont.:
Spec.
PB
Condition
SPEED
sw:
=
HIGH
LINE
cont.:
Spec.
input
condition
©
TEAC
test
tape
TAPE
sw:
EE
MIC
cont.:
Min
YTT-8013:
Blank
tape
for
NORMAL
MONITOR
sw:
TAPE
BIAS
FINE
cont.:
Center
YTT-8053:
Blank
tape
for
EE
TP.05/TP.15:
Min. reading
NAP ARN BR
TP.01/TP.11:
Min. reading
NAP AN se)
AC voltmeter between 2
TP.05/TP.15 and GND | No signal
diyl L306/L406
YTT-8053 sscobid
Bias frequency
Nt P AAR
150 kHz
10. Bias trap
Cae
AC
voltmeter
between
F
TP.01/TP.11
and
GND
|
No
signal
L301/L401
YTT-8053 wes
First
set
adjustor
fully
CCW
(€)),
then
adjust.
Aanic
FHSAA
MITED
LTSBUTHSMEEMOS.
;
FWD
OUTPUT:
Roe
as
ae
R572/R972|
Over-bias
value
(6.15
mV)
REV
AHN
+
INA
PAS
.
R573/R973
2.5
dB
11, Recore bias
YTT-
wee <47% TT-8053
SPEED sw: HIGH
TAPE sw: EE
7