Technics SL-P999 Service Manual

SL-P999 SL-P999
Mi LOCATION OF CONTROLS
The functions indicated by the black numbers (with white background, @ etc.) can be also activated using the remote control transmitter.
1 2 3 (4) ANON BGO @ @ 49
Be ee ere 2)
Ts
|
==
==-22
55-6!
|
EY
saree
ve
a
ooo
;
;
Oe sot torah” [bask] [A=B]IC)emphess
[eee eS :
© eee | (Ee
ee PI -10 -6 76min OdB
aE, Se en eee Ee) er DES al
Nee ie ese Pe
or
ok) 27 6)
Control section
1 ) Power switch (power)
2] Disc holder
© Remote control signal sensor
(remote sensor)
(4) Numeric buttons (+10, 0, 1~20)
(S) Clear button (clear)
This button can be used to clear tracks from the programmed
sequence one at a time.
© Programmed-play button (program)
Time mode select button (time mode)
@5 Display mode select button (display mode)
® Digital output button (digital output) .
This button can be used to switch to on and off for digital
output.
Auto cue/auto space button
(jauto_cue]/[edit] auto space)
Pressing this button causes the unit to switch to the play
standby mode.
When editing, this button can be used to insert the silent gaps
Indicators section
€) Random play indicator (random)
@ Programmed-play indicator (program)
@
Disc
indicator
(Cas)
® Track number display (track)
@ Index/program number display (index/No.)
€ Time display (min/sec)
The indicators display the following types of time information.
“elapsed”: time elapsed since the beginning of the current
Unnumbered buttons on the remote
control transmitter function identically
to their corresponding parts on the
unit.
€ “Over” mark (>)
This indicator lights if the total number of tracks on the disc is
21 or more.
@® Play position/output level indicator
This indicator toggles between its 2 modes each time the
display mode select button is pressed.
@ Track number indicator (4-20)
@ Disc link indicator ( [iink])
Pressing this button initiates the programmed play mode. You Dewan Wie raet. selection ® Compact disc edit indicator ( [edit] )
can then enter specific tracks using the numeric buttons. Random play button (random) “remain”: time remaining until the end of the current Doe Bene
This button can be used to play the tracks on a disc in a selection ® Tape side indicator ((side] A/B)
@)
Recall
button
(recall)
random
sequence.
“total”:
total
elapsed
time
since
the
beginning
of
the
This button can be used to display the contents of the
programmed track sequence for confirmation.
Window search button (window)
Press this button to perform searches when the unit is in the
pause mode. Search for any point on the disc using the
search dial. Release the dial at the desired point and that
Repeat button (repeat)
QQ A-B repeat button (A-B repeat)
This button can be used to play the portion of a disc between
two points (A and B) chosen by you.
3) Play button and indicator (P play)
disc or total time remaining until the end of the
disc, depending on whether the “elapsed” or
“remain” indicator is illuminated.
& Operation indicators
The indicators below illuminate during their respective opera-
tions.
point on the disc is repeated again and again. wt ae Seg
: [edit] @) Pause button and indicator (11 pause) Ceindow <==) window search
o ie pening dae nN re Bains fate @) Stop button (™@ stop) — an ae Remote control transmitter
en ; :
can be used to calculate the number of tracks that can be This button can be used to stop disc play, as well as to cancel [peak]: peak level search ; —, :
recorded on each side of the tape, depending on the length of the various play modes. (a=B): A-B peak level search and A-B repeat play @ Remote control signal transmission window
the cassette tape used, so that as little tape as possible is @4) Index skip buttons (——index/index—) : repeat play @ Search buttons (<< search >P)
wasted.
@ Tape-side select button (side A/B)
When recording compact discs to tape, this button can be
used to check the number of tracks and amount of tape left
over for side A or B.
@® Disc link button (disc link)
This button can be used for edit recording from several discs.
@ Search dial (search)
This dial can be used to locate specific places on the disc
during play at high speed, either forward or reverse.
q Peak level search button (peak search)
This button can be used to locate the maximum signal level
(peak level) for the signals on the disc.
These buttons can be used to skip by index number (smaller
divisions within specific tracks).
@) Skip buttons (4 skip/skip >> )
These buttons can be used to skip by track in the forward or
reverse direction.
@6) Disc holder open/close button (4 open/close)
@ Timer start switch (4 timer)
This switch allows you to use a separately purchased audio
timer to switch the unit on automatically at a preset time.
@® Headphones volume control (phones level)
Avoid listening to music at high volume levels for
extended periods of time.
€) Headphones jack (phones)
€P Digital output indicator ( )
€) Emphasis indicator (emphasis)
This indicator illuminates when discs recorded with pre-
emphasis in the high-frequency range are played.
These buttons can be used to move rapidly forward or
backward on the disc during play. The search speed is slow
when the button is pressed at first and becomes faster if the
button is pressed and held continuously.
@ Display switch (display on/off)
This switch allows you to turn off the display during play if you
wish.
The display returns for about 5 seconds whenever an
operation button is pressed and then goes out again.

Technics SL-P999 Specifications

General

Brand	Technics
Model	SL-P999
Category	CD Player
Language	English