Technics SX-KN200 Owner's Manual

Part III
Recording and playback
Playing back the recorded performance
1. Press to turn on the SEQUENCER button(s)
for the parts of the performance you wish to
have
played back.
KN200
--- SEQUENCER - --
STEP ACCOMP/
RECORD RECORD POLY CHORD
000 0
0000
KN400
---- SEQUENCER ----
STEP ACCOMP/
RECORD RECORD POLY 1 POLY 2 CHORD
00000
00000
• Make sure that only the SEQUENCER in-
dicators for the parts
you wish to have played
back are lit. (If the SEQUENCER indicator for
another part is turned on, the wrong
melody
may be played or the rhythm may stop during
the performance.)
2. Press the SEQUENCER RESET button.
FILL IN
(SEQUENCER RESET)
( )
3. Press the START/STOP button to begin the
automatic
playback.
START/STOP
o
( )
• Use the START/STOP button to start playback
even if the song has no rhythm.
• If the START/STOP button is pressed during
automatic
playback of the recorded perfor-
mance,
playback will stop. If the START/STOP
button is pressed again, playback will continue
from the point at which it stopped. Note, how-
ever, that if the rhythm was stored with the
song, the rhythm does not start in this case.
SEQUENCER RESET
FILL IN
(SEQUENCER RESET)
( )
When the START/STOP button is off, by press-
ing the
SEQUENCER RESET button for 1-2
seconds, the indicators for the parts which
have been stored turn
on and the panel settings
change to the settings at the beginning of the
stored performance.
• If the START/STOP button is pressed during
automatic
playback of a performance, to
return to the beginning of the performance,
press the
SEQUENCER RESET button.
Part III
Advanced applications
Storage capacity
Expressed in terms of notes, the total storage
capacity
of the SEQUENCER is approximately
1600
notes.
• Data such as sound changes etc. can be stored
for
each part, but will reduce the storage
capacity
accordingly.
Recording and playback
• How to count the number of notes
The cycle of one key being pressed and
released is counted as one note.
• When the remaining storage capacity becomes
20% or less, it is shown as a percentage (%)
on the display.
•
When "0" is shown on the display and the
"beep, beep, beep" error message sounds, no
more data can
be stored in the SEQUENCER.
• The tempo can be freely adjusted during
playback. Therefore, you may record the per-
formance by
playing the keyboard slowly.
• If
new songs are stored over songs already
stored, the previously stored songs are erased.
Storing two or more parts at the same time
By setting up the SEQUENCER to record multiple
tracks, you can perform and record multiple parts
at one time.
(KN400)
- --- SEQUENCER ----
STEP ACCOMP /
RECORD RECORD POLY 1 POLY 2 CHORD
0 0000
00000
1. Set the beginning sounds and effects before
starting to
play.
2. Press the RECORD button in the SEQUEN-
CER section. Its indicator lights.
RECORD
o
o
3. Press the SEQUENCER buttons for the parts
you wish to store.
The indicators flash slowly.
(KN400)
4. Play.
ACCOMP/
POLY 1 POLY 2 CHORD
000
000
• Keyboard sounds are produced according to
the
CONDUCTOR settings.
• KN400: When storing the POLY 1 or POLY
2 part, select the respective part on the CON-
DUCTOR before selecting the sound.
• When recording the ACCOMP/CHORD track
during
multiple-track recording, be sure to
turn
on the ONE-FINGER or FINGERED but-
ton of the
AUTO PLAY CHORD before storing
chords.
• KN400: When recording both the POLY 2 and
ACCOMP/CHORD tracks, turn off the AC-
COMP PART 2 and 3 buttons.
5. When you have finished playing, press the
RECORD button to turn it off.
RECORD
o

Technics SX-KN200 Specifications

General

Brand	Technics
Model	SX-KN200
Category	Electronic Keyboard
Language	English