Tecomec Super Jolly - Chain Sharpening Data; Chain Pitch and Gauge Specifications; Vise, Top Plate, and Tilt Angle Settings; Depth Gauge Settings by Chain Type

16
A
÷ 2
B C D E F
CHAIN PITCH GAUGE VISE ANGLE TOP PLATE ANGLE TILT ANGLE DEPTH GAUGE
1/4” 0.050”/1.3mm 30° 55° / 60° 10°
.025”/0.63mm
0.325” 0.050”/1.3mm 30° 55° / 60° 10° .025”/0.63mm
0.325” 0.058”/1.5mm 30° 55° / 60° 10° .025”/0.63mm
0.325” 0.063”/1.6mm 30° 55° / 60° 10° .025”/0.63mm
0.325” 0.050”/1.3mm 25° 55° / 60° 10° .025”/0.63mm
0.325” 0.058”/1.5mm 25° 55° / 60° 10° .025”/0.63mm
0.325” 0.063”/1.6mm 25° 55° / 60° 10° .025”/0.63mm
0.325” 0.050”/1.3mm 25° 55° / 60° 10° .025”/0.63mm
0.325” 0.058”/1.5mm 25° 55° / 60° 10° .025”/0.63mm
0.325” 0.063”/1.6mm 25° 55° / 60° 10° .025”/0.63mm
0.325” 0.050”/1.3mm 30° 60° 10° .025”/0.63mm
0.325” 0.058”/1.5mm 25° 60° 10° .025”/0.63mm
0.325” 0.063”/1.6mm 25° 60° 10° .025”/0.63mm
0.325” 0.050”/1.3mm 5° 50° 0° .025”/0.63mm
3/8” 0.058”/1.5mm 25° 60° 10° .025”/0.63mm
3/8” 0.063”/1.6mm 25° 60° 10° .025”/0.63mm
3/8” 0.050”/1.3mm 35° 55° / 60° 0° .025”/0.63mm
3/8” 0.050”/1.3mm 35° 55° / 60° 0° .025”/0.63mm
3/8” 0.058”/1.5mm 35° 55° / 60° 0° .025”/0.63mm
3/8” 0.058”/1.5mm 35° 55° / 60° 0° .025”/0.63mm
3/8” 0.063”/1.6mm 35° 55° / 60° 0° .025”/0.63mm
3/8” 0.063”/1.6mm 35° 55° / 60° 0° .025”/0.63mm
3/8” 0.050”/1.3mm 25° 55° / 60° 10° .025”/0.63mm
3/8” 0.058”/1.5mm 25° 55° / 60° 10° .025”/0.63mm
3/8” 0.063”/1.6mm 25° 55° / 60° 10° .025”/0.63mm
3/8” 0.050”/1.3mm 25° 55° / 60° 10° .025”/0.63mm
3/8” 0.058”/1.5mm 25° 55° / 60° 10° .025”/0.63mm
3/8” 0.063”/1.6mm 25° 55° / 60° 10° .025”/0.63mm
3/8” 0.050”/1.3mm 10°-15° 50° 10° .025”/0.63mm
3/8” 0.058”/1.5mm 10°-15° 50° 10° .025”/0.63mm
3/8” 0.063”/1.6mm 10°-15° 55° / 60° 10° .025”/0.63mm
3/8” 0.050”/1.3mm 5° 60° 0° .025”/0.63mm
3/8”(90) 0.043”/1.1mm 30° 50° / 55° 0° .025”/0.63mm
3/8” 0.050”/1.3mm 30° 55° / 60° 0° .025”/0.63mm
3/8” 0.050”/1.3mm 30° 60° 0° .025”/0.63mm
3/8” 0.050”/1.3mm 30° 60° 0° .025”/0.63mm
0.404” 0.058”/1.3mm 35° 60° 10° .030”/0.76mm
0.404” 0.058”/1.3mm 35° 60° 10° .030”/0.76mm
0.404” 0.063”/1.5mm 35° 55° / 60° 10° .030”/0.76mm
0.404” 0.063”/1.5mm 35° 55° / 60° 10° .030”/0.76mm
0.404” 0.063”/1.6mm 10°-15° 50° 10° .030”/0.76mm
0.404” 0.063”/1.6mm 10°-15° 50° 10° .030”/0.76mm
0.404” 0.063”/1.6mm 35° 55° / 60° 10° .030”/0.76mm
0.404” 0.063”/1.6mm 35° 55° / 60° 10° .030”/0.76mm
0.404” 0.058”/1.5mm 25° 55° / 60° 10° .030”/0.76mm
0.404” 0.063”/1.6mm 25° 55° / 60° 10° .030”/0.76mm
0.404” 0.063”/1.6mm 35° 60° 10° .050”/0.76mm
0.404” 0.080”/2.0mm 35° 60° 10° .050”/0.76mm
3/4” 0.122”/3.1mm 30° 50° 0° .050”/0.76mm
3/4” 0.122”/3.1mm 35° 60° 0° .070/1.77mm
DOWN
ANGLE