Teka CLC - Adjusting Coffee Temperature Settings

16
17
• Make sure the appliance is ready and the
water softener filter has been removed.
• PresstheMENUbutton(B6)thenpressthe
NEXT button (B7) repeatedly until the ap-
pliance displays “DESCALE NO”.
• PresstheCHANGEbutton(B8)andtheap-
pliance displays “DESCALE YES”.
• PresstheOKbutton(B9)tostartthedescale
programme. The appliance displays “ADD
DESCALER PRESS OK”.
• Emptythewatertank,pourthecontentsof
the descaler bottle into the tank respecting
the instructions given on the descaler pack,
then add water.
When descaling subsequently, use desca-
ler of the same type and brand as supplied
(available from the manufacturer’s autho-
rised Customer Services) or a descaler re-
commended by Customer Services. Always
follow the instructions on the pack.
• Attachthecappuccinomakertothenozzle.
• Placeacontainerwithaminimumcapacity
of 2 litres under the cappuccino maker (fig.
3).
• PresstheOKbutton.Descalerflowsoutof
the cappuccino maker into the container
below. “APPLIANCE IN DESCALE” is di-
splayed.
• Thedescaleprogrammeautomaticallyper-
forms a series of deliveries and pauses to
remove limescale deposits from inside the
machine.
• After about 30 minutes, the appliance di-
splays “RINSING FILL TANK”.
The appliance must now be rinsed through
to eliminate residues of descaling solution
from inside the appliance. Proceed as fol-
lows:
• Empty the water tank, rinse and fill with
clean water.
• Replacethetank;
• Emptythefullcontainerandputbackunder
the cappuccino maker.
• PresstheOKbutton.Hotwaterflowsoutof
the cappuccino maker spout into the contai-
ner below and the appliance displays “RIN-
SING”.
• Whenthewatertankisempty,theappliance
displays the message “RINSING COMPLETE
PRESS OK”.
• PresstheOKbuttonandrefillthewatertank
with clean water.
• Thedescaleprogrammeisnowterminated
and the appliance is ready to make coffee
again.
NOTE: If descaling is interrupted before
completion, the machine still displays the
descaling message and the process must be
begun again from the beginning.
Empty the water tank, rinse with clean water
and deliver a cup of hot water.
Important! FAILURE TO DESCALE THE
APPLIANCE REGULARLY INVALIDATES THE
GUARANTEE.
Changing coffee temperature
To change coffee temperature, proceed as fol-
lows:
• PresstheMENUbutton(B6),thenpressthe
NEXT button (B7) repeatedly until the ap-
pliance displays “TEMPERATURE MEDIUM”.
• PresstheCHANGEbutton(B8)untiltheap-
pliance displays the required coffee tempera-
ture.
• PresstheOKbutton(B9)toconfirm.
• PresstheMENUbuttontoexitprogramming
mode or NEXT to change other parameters.
Changing the length of time the
appliance remains on
The appliance is set by default to go off automa-
tically 30 minutes after the last coffee has been
made. To change this interval (max. 180 min),
proceed as follows:
• PresstheMENUbutton(B6)thenpressthe
NEXT button (B7) repeatedly until the ap-
pliance displays: “OFF AFTER 30 MIN”.
• PresstheCHANGEbutton(B8)tochangethe
number of time the appliance remains on.
• PresstheOKbutton(B9)toconfirm.
• PresstheMENUbuttontoexitprogramming
mode or NEXT to change other parameters.