Mechanical Parts List— Type 422 AC-DC
FIG. 2
Fig. & Q
Index Tektronix Serial/Model No. f
No. Part No. Eff Disc y
2-1
179-0941-02 20000
303999
1
179-0941-03 304000
1
-2
131-0371 -00
1
-3
670-0407-02 20000
24999
1
670-0407-03 25000
1
388-0616-02
1
-4
214-0507-00
22
-5
337-0717-00
1
-6
129-0069-00
2
361-0008-00
1
-7
344-0119-00
6
-8 136-0220-00
7
-9
211-0116-00
4
210-0994-00
3
210-0406-00
1
-10
407-0103-00
1
-11 175-0582-00
1
175-0583-00
1
175-0584-00
1
175-0596-00
1
-12
214-0153-00
1
-13
214-0511-00
2
211-0007-00
1
-14 214-0317-00
20000
20449
2
214-1138-00 20500
2
-15
352-0082-00
2
-16 407-0104-00
1
211-0008-00
3
-17
348-0063-00
5
-18
343-0089-00
2
-19
343-0006-00
1
211 -0097-00
1
210-0851-00
1
-20
210-0201-00
3
1
CHASSIS
Description
1 2 3 4 5
CABLE HARNESS, vertical
CABLE HARNESS, vertical
cable harness includes:
CONNECTOR, single contact, female
ASSEMBLY, circuit board—SWITCHING & OUTPUT AMPLIFIER
ASSEMBLY, circuit board—SWITCHING & OUTPUT AMPLIFIER
assembly includes:
BOARD, circuit
board includes:
PIN, connector, 45°, male
SHIELD, horizontal amplifier
POST, tie-off
mounting hardware for each: (not included w/post)
SPACER, plastic, 0.281 inch long
CLIP, electrical
SOCKET, transistor, 3 pin
mounting hardware: (not included w/assembly)
SCREW, sems, 4-40 x 5/16 inch, PHB
WASHER, flat, 0.125 ID x 0.250 inch OD
NUT, hex., 4-40 x 3/u inch
BRACKET, vertical board
WIRE, CRT lead, 0.458 foot, striped brown, w/connector
WIRE, CRT lead, 11 ]/ 2 inches, striped red, w/connector
WIRE, CRT lead, 11 ]/ 2 inches, striped green, w/connector
WIRE, CRT lead, 0.417 foot, striped blue, w/connector
FASTENER, snap, double-pronged
SPRING, transistor mounting
mounting hardware for each: (not included w/spring)
SCREW, 4-40 x 3/w Inch, PHS
HEAT SINK, insulator disc
HEAT SINK, insulator disc
HOLDER, transistor mounting
BRACKET, vertical output
mounting hardware: (not included w/bracket)
SCREW, 4-40 x V4 inch, PHS
GROMMET, plastic, y2 inch diameter
CLAMP, cable, plastic, size "D"
CLAMP, cable, plastic, y2 inch
mounting hardware: (not included w/clamp)
SCREW, 4-40 x 5/ u inch, PHS
WASHER, flat, 0.119 ID x % inch OD
LUG, solder, SE #4
mounting hardware for each: (not included w/lug)
SCREW, thread forming, 5-32 x 3/ u inch, PHS
213-0044-00
To Next Page
Loading...
