Tektronix T922 User Manual

CALIBRATION TEST EQUIPMENT
REPLACEMENT
Calibration Test Equipment Chart
This chart compares TM 500 product performance to that of older Tektronix equipment . Only those
characteristics where significant specification differences occur, are listed . In some cases the new instrument
may not bea total functional replacement . Additional support instrumentation may be
needed
or
a change in
calibration procedure may be necessary .
NOTE : All TM
500
generator outputs are short-proof . All TM
500 plug-in instruments require TM 500-Series Power Module .
REV . A, OCT 1975
Comparison of Main Characteristics
- Amplitude range 40 mV to 10 V p-p .
- Frequency range
350 kHz to 100 MHz .
-
Frequency
range 65 MHz to 500 MHz .
Marker outputs, 5 sec to 1 /is .
Sinewave available at 20, 10,
and 2 ns . Trigger pulses 1, 10,
100 Hz ; 1, 10, and 100 kHz .
Multiple time-marks can
be
generated simultaneously .
- Marker outputs, 1, 10, 100, 1000,
and 10,000 Ns, plus 10 ns sinewave
.
- Marker outputs, 5 sec to
2
ns
. Sine-
wave available at 50,
20, 10, 5,
and 2 ns .
Separate trigger pulses
of 1 and .1 sec ; 10, 1, and .1 ms ;
10 and 1 Ns . Marker amplifier pro-
vides positive or negative time
marks of 25 V min . Marker
intervals of 1 and .1 sec ;
10, 1,
and .1
ms ; 10 and 1
/is .
- Marker outputs, 5 sec to 0 .1 ps .
Sinewave available to 50, 10,
and 5 ns . Separate trigger pulses,
from 5 sec to 0 .1 ps .
Multiple
time-marks can be gene-
rated simultaneously .
190A, 190B
191
067-0532-01
SG 503 - Amplitude range 5 mV to 5 .5 V p-p .
SG 503 - Frequency range 250 kHz to 250 MHz .
SG 503 - Frequency range 250 kHz to 250 MHz .
190B
191
0532-01
TG 501 replaces 180,
180A TG 501 Marker outputs, 5 sec to 1 ns .
180A
Sinewave available at 5,
2, and 1 ns .
Trigger output - slaved to marker
output from 5 sec through 100 ns .
One time-mark can be generated at a
time .
181 TG 501 Marker outputs, 5 sec to
1
ns .
Sine- 181
wave available at 5, 2, and 1 ns .
184 TG 501 Marker outputs, 5 sec to 1 ns . Sine- 18
wave available at 5, 2, and 1 ns .
Trigger output - slaved to marker
output from 5 sec through 100 ns .
One time-mark can be
generated at
a time .
2901 TG 501 Marker outputs, 5 sec to
1
ns .
Sine-
2901
wave available at 5, 2, and 1 ns .
Trigger output - slaved to marker
output from 5 sec through 100 ns .
One time-mark can be generated at
a
time .
DM 501 replaces 7D13
PG 501 replaces 107 PG 501 - Risetime less than 3 .5 ns into 107-
Risetime
less than 3 .0 ns
into
500 . 50
O .
108 PG 501 - 5 V output pulse ; 3 .5 ns Risetime . 108-
10 V output pulse ; 1 ns Risetime .
111 PG 501 - Risetime less than 3 .5 ns ; 8 ns
111 - Risetime 0 .5 ns ; 30 to 250 ns
Pretrigger pulse delay .
Pretrigger Pulse delay .
114 PG 501 - ±5 V output . 114- ±10V output . Short proof output .
115 PG 501 - Does not have Paired, Burst, Gated, 115- Paired, Burst, Gated, and Delayed
or Delayed pulse mode ; ±5V do pulse mode ;
±10V output .
Offset . Has ±5
V output . Short-proof output .
PG 502 replaces 107
108 PG 502 - 5 V output 108 - 10 V output
.
111 PG 502 -
Risetime
less
than 1 ns ; 10 ns 111 - Risetime 0 .5 ns ; 30 to 250 ns
Pretrigger pulse delay .
Pretrigger pulse delay .
114 PG 502 - ±5 V output 114
-
±10V output . Short proof output .
115 PG 502 - Does not have Paired, Burst, Gated, 115 - Paired, Burst, Gated, Delayed
&
Un-
Delayed & Undelayed pulse mode ; delayed pulse mode ; ±10 V output
.
Has ±5V output . Short-proof output
.
2101 PG 502 - Does not have Paired or Delayed 2101 - Paired and Delayed pulse ;
10 V
pulse . Has ±5
V
output
.
output
.
PG 506 replaces 106 PG 506 - Positive-going trigger output signal 106 - Positive and
Negative-going trigger
at least 1 V ; High Amplitude out- output signal, 50
ns and 1 V ; High
put, 60 V .
Amplitude output, 100 V .
067-0502-01
PG
506 - Does not have chopped feature . 0502-01 - Comparator output can be alter-
nately chopped to a reference
voltage .
SG 503 replaces 190,

Tektronix T922 Specifications

General

Brand	Tektronix
Model	T922
Category	Test Equipment
Language	English