Tektronix TDS 500D series - Figure 1-13: Measurement of Accuracy - Long-Term and Delay Time

154 pages

To Next Page

To Previous Page

Performance Tests

1–48

TDS 500D, TDS 600B & TDS 700D Performance Verification and Specifications

Check long–term sample

rates and delay time

accuracies against limits.

Align the trigger T to the

center graticule line.

Set

horizontal

mode.

Set horizontal scale

and delayed time.

Figure 1–13: Measurement of accuracy – Long-term and delay time

3. Disconnect the hookup: Disconnect the cable from the generator output at

the input connector of CH 1.

Main Page

Table of Contents5
General Safety Summary9
Preface13
Contacting Tektronix14
Performance Verification Procedures15
Input Channels Vs. Model18
Conventions18
Figure 1-1: Map of Display Functions19
Brief Procedures21
Self Tests21
Figure 1-2: Verifying Adjustments and Signal-Path Compensation22
Functional Tests23
Figure 1-3: Universal Test Hookup for Functional Tests - TDS 600B Shown24
Prerequisites31
Equipment Required32
Table 1-1: Test Equipment32
TDS 600B Test Record34
TDS 500D/700D Test Record38
TDS 794D Test Record42
Signal Acquisition System Checks45
Table 1-2: DC Offset Accuracy (Zero Setting)46
Figure 1-4: Measurement of DC Offset Accuracy at Zero Setting47
Figure 1-5: Initial Test Hookup48
Table 1-3: DC Voltage Measurement Accuracy50
Figure 1-6: Measurement of DC Accuracy at Maximum Offset and Position51
Figure 1-7: Initial Test Hookup53
Figure 1-8: Optional Initial Test Hookup53
Table 1-4: Analog Bandwidth55
Figure 1-9: Measurement of Analog Bandwidth56
Figure 1-10: Initial Test Hookup58
Figure 1-11: Measurement of Channel Delay - TDS 684B Shown60
Table 1-5: Delay between Channels Worksheet61
Time Base System Checks62
Figure 1-12: Initial Test Hookup62
Figure 1-13: Measurement of Accuracy - Long-Term and Delay Time64
Trigger System Checks65
Figure 1-14: Initial Test Hookup66
Figure 1-15: Measurement of Time Accuracy for Pulse and Glitch Triggering67
Figure 1-16: Initial Test Hookup69
Table 1-6: Trigger Level Accuracy Readout70
Figure 1-17: Measurement of Trigger-Level Accuracy71
Table 1-7: Delayed Trigger Level Accuracy Readout72
Figure 1-18: Initial Test Hookup74
Figure 1-19: Measurement of Trigger Sensitivity - 50 Mhz Results75
Output Signal Checks78
Figure 1-20: Initial Test Hookup78
Figure 1-21: Measurement of Main Trigger out Limits80
Figure 1-22: Initial Test Hookup82
Figure 1-23: Measurement of Probe Compensator Frequency84
Figure 1-24: Subsequent Test Hookup85
Figure 1-25: Measurement of Probe Compensator Amplitude86
Option 05 Video Trigger Checks (Not Available on TDS 794D)87
Figure 1-26: Jitter Test Hookup88
Figure 1-27: Jitter Test Displayed Waveform - TDS 684B Shown89
Figure 1-28: Jitter Test When Completed - TDS 684B Shown90
Figure 1-29: Triggered Signal Range Test - 300 MV91
Figure 1-30: Triggered Signal Range Test - 75 MV92
Figure 1-31: 60 Hz Rejection Test Hookup93
Figure 1-32: 60 Hz Rejection Test Setup Signal93
Sine Wave Generator Leveling Procedure104
Optical Filters Checks (TDS 500D/TDS 700D Only)107
Table 1-8: Available Filters107
Table 1-9: Reference Receiver Filter Options107
Table 1-10: Option 3C and 4C Specifications108
Table 1-11: Available Receivers108
Table 1-12: Bessel Thompson Frequency Response and116
Specifications119
Product Description121
Table 2-1: Key Features of the TDS 500D, 600B and121
User Interface122
Signal Acquisition System123
Horizontal System123
Table 2-2: Record Length and Divisions Per Record Vs. TDS Model124
Trigger System125
Acquisition Control126
On-Board User Assistance127
Measurement Assistance127
Storage128
I/O128
Display129
Nominal Traits131
Table 2-3: Nominal Traits - Signal Acquisition System131
Table 2-4: Nominal Traits - Time Base System132
Table 2-5: Nominal Traits - Triggering System133
Table 2-6: Nominal Traits - Display System135
Table 2-7: Nominal Traits - GPIB Interface, Output Ports, and Power Fuse136
Table 2-8: Nominal Traits - Data Handling and Reliability136
Table 2-9: Nominal Traits - Mechanical137
Warranted Characteristics139
Table 2-10: Warranted Characteristics - Signal Acquisition System140
Table 2-11: Warranted Characteristics - Time Base System142
Table 2-12: Warranted Characteristics - Triggering System142
Table 2-13: Warranted Characteristics - Output Ports143
Table 2-14: Warranted Characteristics - Environmental144
Table 2-15: Certifications and Compliances146
Typical Characteristics147
Table 2-16: Typical Characteristics - Signal Acquisition System147
Table 2-17: Typical Characteristics - Triggering System150

Tektronix TDS 500D series - Figure 1-13: Measurement of Accuracy - Long-Term and Delay Time

Table of Contents

Other manuals for Tektronix TDS 500D series

Related product manuals