Tektronix TDS 500D series - Page 8

Table of Contents
iv
TDS 500D, TDS 600B & TDS 700D Performance Verification and Specifications
List of Tables
Table 1–1: Test equipment 1–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–2: DC offset accuracy (zero setting) 1–30. . . . . . . . . . . . . . . . . . . .
Table 1–3: DC Voltage measurement accuracy 1–34. . . . . . . . . . . . . . . . . .
Table 1–4: Analog bandwidth 1–39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–5: Delay between channels worksheet 1–45. . . . . . . . . . . . . . . . . .
Table 1–6: Trigger level accuracy readout 1–54. . . . . . . . . . . . . . . . . . . . . .
Table 1–7: Delayed trigger level accuracy readout 1–56. . . . . . . . . . . . . . .
Table 1–8: Available Filters 1–91. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–9: Reference Receiver Filter Options: 1–91. . . . . . . . . . . . . . . . . . .
Table 1–10: Option 3C and 4C Specifications 1–92. . . . . . . . . . . . . . . . . . .
Table 1–11: Available receivers 1–92. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–12: Bessel Thompson frequency response and
reference receiver limits 1–100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–1: Key features of the TDS 500D, 600B and
700D oscilloscopes 2–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–2: Record length and divisions per record vs. TDS model 2–4. .
Table 2–3: Nominal traits — Signal acquisition system 2–11. . . . . . . . . . .
Table 2–4: Nominal traits — Time base system 2–12. . . . . . . . . . . . . . . . . .
Table 2–5: Nominal traits — Triggering system 2–13. . . . . . . . . . . . . . . . .
Table 2–6: Nominal traits — Display system 2–15. . . . . . . . . . . . . . . . . . . .
Table 2–7: Nominal traits — GPIB interface, output ports, and
power fuse 2–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–8: Nominal traits — Data handling and reliability 2–16. . . . . . . .
Table 2–9: Nominal traits — Mechanical 2–17. . . . . . . . . . . . . . . . . . . . . . .
Table 2–10: Warranted characteristics — Signal acquisition system 2–20
Table 2–11: Warranted characteristics — Time base system 2–21. . . . . . .
Table 2–12: Warranted characteristics — Triggering system 2–22. . . . . .
Table 2–13: Warranted characteristics — Output ports,
probe compensator, and power requirements 2–23. . . . . . . . . . . . . . . .
Table 2–14: Warranted characteristics — Environmental 2–24. . . . . . . . .
Table 2–15: Certifications and compliances 2–26. . . . . . . . . . . . . . . . . . . . .
Table 2–16: Typical characteristics — Signal acquisition system 2–27. . .
Table 2–17: Typical characteristics — Triggering system 2–30. . . . . . . . .