To Next PageTo Next PageWhat causes ' output evacuation circuit is disconnected' on Telefire ADR-7000?
If the Telefire Control Panel displays ' output evacuation circuit is disconnected', it means the output evacuation circuit is disconnected at the extinguishing controller. Reconnect the circuit.
What to do if Telefire ADR-7000 says ' sirens circuit is disconnected'?
If the Telefire Control Panel displays an ' sirens circuit is disconnected' message, it indicates that the siren circuit is disconnected at the extinguishing controller. Reconnect the circuit.
What does 'Panel # communication error' mean on Telefire Control Panel?
If the Telefire Control Panel displays 'Panel # communication error,' it means a control panel defined as a Partner is disconnected or powered off. Ensure that the control panel is on and verify the connection.
Why does my Telefire ADR-7000 show 'Main circuit limited current'?
If the Telefire Control Panel displays 'Main circuit limited current' for a device, it means that the current has been limited on the designated device. Locate the source of the fault, such as damaged wire or a water leak, and repair it.
What causes 'Main circuit low voltage' on Telefire ADR-7000 Control Panel?
If the Telefire Control Panel displays 'Main circuit low voltage' for a specific device, it means the voltage is low on that device. If the device is the battery or backup battery (3V), replace the battery or backup battery (R2032C). Otherwise, the control panel may be faulty and should be sent to the manufacturer for repairs.
How to fix 'Main circuit short' on a Telefire ADR-7000 Control Panel?
If the Telefire Control Panel displays 'Main circuit short' for a device, it indicates a short circuit on that device. Find the cause of the short circuit and remove it.
What does 'Main circuit disconnect' mean on my Telefire ADR-7000 Control Panel?
If the Telefire Control Panel shows 'Main circuit disconnect' for a specific device, it means that the designated device is disconnected. Check the line continuity and connect an end of line resistor (5.1K?) at the output circuit connectors.
How to enable a disabled device on Telefire ADR-7000?
If your Telefire Control Panel shows 'Disabled,' it indicates that a device or area has been disabled. To enable it: - Open the start/stop device menu from the main menu. - Select the device or area indicated in the message. - Click 'Enable'.
Compares the ADR-7000 with SAVER-7000 and GUARD-7 models.
Details the ADR-7021 main board, its connectors, and design.
Explains the ADR-7002 line cards for SLC loop communication and LEDs.
Describes the ADR-7003 keyboard and graphic LCD display interface.
Details the ADR-7000's built-in 150W power supply specifications.
Explains the optional ADR-7000ZM module for visual zone alarms.
Describes the LON-7000 module for networking control panels.
Details the NET-7000 module for internet-enabled monitoring and control.
Explains the ADR-7001EM1 card for expanding SLC loops up to 8.
Describes the RM-7000 for remote control and supervision of the panel.
Details the 4 access levels and 6 user types with password protection.
Describes the system's normal operational state with "System OK" status.
Explains the state when a fire alarm condition is detected.
Details the state indicating system or device faults.
Describes the state for monitoring non-fire events like low pressure.
Explains the state when devices or outputs are intentionally disabled.
Describes the state for performing system tests without activating outputs.
Indicates events that are not alarm, fault, supervisory, or disabled.
Covers planning quantity, location of devices, and capacity planning.
Details wiring requirements, cable selection, and length limitations.
Outlines general wiring rules and connection procedures.
Instructions for installing various system components.
Covers final steps after installation, like activation and testing.
Defines how extinguishing outputs and controllers are configured.
Explains how to manually activate extinguishing systems.
Details the configuration of delays for extinguishing activation.
Covers the physical switch for disconnecting extinguishing output.
Describes post-activation notification and refill procedures.
Describes the graphical LCD display for system status and events.
Explains the meaning and behavior of all panel LEDs.
Details the functions of keys used by operators for panel control.
Explains the use of numeric and arrow keys for navigation and input.
Provides a visual overview of the system programming menu hierarchy.
Steps to access the system programming mode with password.
Outlines the five main steps involved in system programming.
Instructions for saving changes and exiting the programming mode.
Sets up system parameters to match site requirements.
Function to temporarily disable or enable devices, zones, or outputs.
Allows graphical display and testing of selected devices.
Provides detailed reports on alarms, faults, tests, and device lists.
Accesses functions like Lamp Test, Clear Extinguisher, Revisions, Keyboard Locking.
Feature to test all initiating devices in the system.
Displays system information like licensing, devices, and connected panels.
Performs tests for the smoke control system functions.
Defines control panel behavior to match specific site requirements.
Allows manual or automatic parameter setting for devices.
Assigns entities to multiple devices for single operations like disablement.
Checks the validity of device programming and communication.
Clears logged alarms, faults, walk tests, and key operations.
Allows changing operator and programmer passwords for security.
Advanced settings, noted as "Not for field use".
Forces the panel to perform detector initialization.
Explains the LEDs on the user display and main board.
Lists and explains error messages related to the control panel.
Details system faults, possible causes, and repair actions.
Guidelines for weekly inspection of the control panel by the site supervisor.
Details the automatic battery supervision and testing process.
Lists addressable and conventional input devices compatible with the system.
Lists compatible addressable output modules and NAC connections.
Lists devices tested and certified for UL compliance.
Provides physical dimensions, operating temp, and voltage specs.
Details the ADR-7000's 150W power supply and battery specifications.
Specifies the number of compatible RM-7000 annunciators.
Describes field connections for NACs, SLC, and 24V outputs on the main board.
Details the configuration and ratings of the main board's relays.
General| Type | Addressable fire alarm control panel |
|---|---|
| Enclosure Protection | IP30 |
| Compatibility | Telefire addressable devices |
| Input Voltage | 230V AC, 50Hz |
| Operating Temperature | +40°C |
| Relative Humidity | up to 95% (non-condensing) |
