(6)
(7)
-23- -25- -27--26- -29- -31-
Tail Boom Bracket Set-4Tail Boom Bracket Set-3Tail Boom Bracket Set-2Tail Boom Bracket Set-1
Step 1
1.Fit the Tail Drive Gear Set to the Tail Boom Bracket.
2.Secure the Tail Boom Bracket Cover to the Tail Boom Bracket.
No.
1
2
3
4
Material No. Description Qty
BK1005
BV1007
BK1006
HMJ2-10N
Tail Boom Bracket
Tail Drive Gear Set
Tail Boom Bracket
Cover
Tapping Screw M2x10
1
1
1
2
(1)
(2)
(3)
(4)
Step 2
Complete
No.
1
2
Material No. Description Qty
HMC2-12B
HML2
Socket Screw M2x12
M2 Nut
2
2
(1)
(2)
T22
No.
1
2
3
4
Material No. Description Qty
BK1082
HMJ12-6B
BK0923
HNN2-10B
Rod Guide
Tapping Screw M1.2x6
Tail Servo Tray
Tapping Screw(W/Washer) M2x10
2
2
2
2
Note:
(1)
(2)
(4)
(3)
No.
1
2
3
4
Material No. Description Qty No.
5
6
7
Material No. Description Qty
HNN2-10B
HMC2-25B
HML2
BK1027
BK1026
HMC2-14B
BK1025
Tapping Screw(W/Washer) M2x10
Socket Screw M2x25
M2 Nut
Tail support Rod
Bracket
Socket Screw M2x14
Rod End
4
2
3
2
1
1
4
Note:
Step 2
1.Apply CA or Epoxy when assembling the Tail Support Rod End.
2.Install the Tail Support Bracket and fit the Tail Support Rod.
Note:2
No.
1
2
3
4
Material No. Description Qty
BK1036
HSA3-5B
HME3-3B
BK1009
Motor mount
Socket Screw M3x5
Set Screw
Drive Gear 13T
1
2
2
1
Step 1
1.Remove the servo wheel prior to attaching the Linkage Ball.
2.Mount the Linkage Ball at 12.5mm from the center of the servo arm.
3.Secure the servo to the right Servo Tray and attach the rod to the servo arm.
Step 2
1.Remove all the servo wheels prior to attaching the Linkage Balls.
2.Mount the Linkage Balls at 12.5mm from the center of the servo arms.
3.Secure the servos to the left and to the back, attach the rods to the servo arms.
Step 1
1.Attach the receiver, gyro to the Main Frame by Double Side Tap.
2.Insert the Antenna Tube and fix it by the Rubber Tube.
Step 2
Set the battery on the tray by Rubber Band.
Step 1
1.Cut off the unnecessary part from the body and the canopy.
2.Attach the canopy to the body by 3 self-tapping screws.
3.Insert the Rubber Grommet to the body as shown.
Step 2
Cut the Body as shown.
No.
1
2
3
4
5
6
7
Material No. Description Qty
BK1061
BK1067
BK1068
HSP16-6N
HMC3-20B
HMM3Z
JD0451
Main Rotor Blade
Upper Blade Grip
Lower Blade Grip
Countersunk Screw M1.6x6
Socket Screw M3x20
M3 Nylon nut
Sticker for C.G
2
2
2
2
2
2
1
(4)
(2)
(1)
(3)
Step 2
1.Secure the blades to the Main Rotor
Pitch Housing.
2.It is suggested to balance the blades.
(5)
(5)
(6)
(6)
(3)
(4)
16mm
(2)
(1)
(3)
(4)
(5)
T22
(1)
(2)
(3)(1)
No.
1
2
3
4
Material No. Description Qty
BK1087
BK1076
HMJ12-3B
BK1002
Canopy
Body
Tapping Screw M1.2x3
Rubber Grommet
1
1
3
2
No.
5
6
7
Material No. Description Qty
BK1016
HMC3-10B
HMM3Z
Drive Gear 15T
Socket Screw M3x10
M3 Nylon nut
1
2
2
-28-
Step 1
1.Pull the belt through the Tail Boom Bracket and keep the belt correctly aligned.
2.Push the Tail Boom into the Tail Boom Bracket and the Tail Drive Belt must be rotated as
shown below.
Step 2
1.Place the belt over the Pulley
and gently pull back the Tail
Boom until the tension of the
belt allows no more than
5mm of free play.
2.Fix the Tail Boom in the
bracket with the Socket
Screws and M2 nuts. Do not
forget to apply Loctite on the
screws.
Step 1
1.Install the Rod Guides and the Tail Servo Tray.
2.Secure the self-tapping screws but not tighten them at this moment so that you can adjust
later.
Step 1
1.Slide the Tail Boom Set into the Main Frame.
2.Push it on the bracket instead of pushing the Tail Boom.
3.Secure the Tail Boom Set and do not forget to add Loctite on the screws.
-30- -32-
Step 1
1.Mount the motor to the Motor Mount.
2.Secure the Drive Gear to the motor shaft. Note that the distance from the end of the Drive
Gear to the Motor Mount should be around 16mm as shown.
Note:1
1.The OBL 29/35-10H(No.2381) Brushless Motor and
13T pinion are recommended for mini Titan E325
with ACE POWER 3S1P Li-Po battery.
2.The OBL 29/35-10H(No.2381) Brushless Motor and
15T pinion are recommended for mini Titan E325
with ACE POWER 2S1P Li-Po battery.
Step 2
1.Attach the motor and the Motor Mount to the
Main Frame.
2.Adjust the gear mesh and secure the Motor
Mount on the chassis.
You can observe the gear mesh from the
bottom of Base Plate.
Step 1
1.Remove the tail servo wheel prior to attaching the Linkage Ball.
2.For the rudder servo, mount the Linkage Ball at 10.5mm from the center of the servo arm
as beginning. Please refer to the manual of your gyro to choose the length of the arm.
3.Secure the servo to the Tail Servo Tray and attach the rod to the servo arm.
No.
1
2
3
Material No. Description Qty
BK1028
BK1088
BK1038
Antenna Tube
Rubber Tube 10mm
Landing Skid Damper
1
2
4
Step 1
1.For safety concern, be sure to modify the main blades as following.
2.Mark around the blade grips with a felt tip marker.
3.Remove the blade grips and cut the covering gently around 1mm inside of the mark. Be
careful not to hurt the blades.
4.Sand the inside of the grips lightly for better adhesion. Apply CA or Epoxy to blades in area
as shown.
5.Attach blade grips and tighten the screws.
6.Wipe off the excess CA or Epoxy.
Gyro
Receiver
Double Side Tap
Double Side Tap
Li-Po Battery
(1)
(2)
CA Glue
or Epoxy
CA Glue
or Epoxy
Electric System-1 Electric System-3 Canopy Assembly
No.
1
2
3
4
Material No. Description Qty
BK1071
BK0922
BK1203
HSP16-6N
Tail Linkage Rod D1.3
Ball Link 3.8x12mm
Linkage Ball( 3.8)
Countersunk Screw M1.6x6
1
2
4
4
(3)
(4)
(1)
(2)
Note:
6mm
Bag J Bag J Bag J Bag J Bag K Bag L Bag L Bag M
-24-
T22
T22
(1)
(6)
(4)
(5)
(3)
(1)
T22
(7)
(1)
(2)
(3)
CA or Epoxy
To Next Page
Loading...
