EasyManua.ls Logo

TIC TFS12 - User Manual

TIC TFS12
10 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
T
T
F
F
S
S
1
1
2
2
“
“
S
S
t
t
e
e
r
r
e
e
o
o
”
”
O
O
u
u
t
t
d
d
o
o
o
o
r
r
R
R
o
o
c
c
k
k
S
S
p
p
e
e
a
a
k
k
e
e
r
r
s
s
TIC TFS12 “Stereo” Outdoor Rock Speakers Feature
Weatherproof Design
Teflon® sealed cabinetry
Aluminum Grill
Full range 200W speaker system
8” woofer driver
2x 1” aluminum tweeters
Surge protected Revchem®
8 Ohm Impedance, 2x 4 Ohm
Stereo mode
Aerospace grade multi-layer
composite cabinetry
Surface mount waterproof cable
connector
Finishes: Canyon (CN) Slate
(SL) or White Granite (WG)
©TIC Corporation U.S.A.

Table of Contents

Other manuals for TIC TFS12

Preview: Specifications
Specifications1 page

Questions and Answers

  • A
    adamsjessicaJul 26, 2025
    What to do if my TIC TFS12 Speakers have no sound?
    • C
      Corey HuangJul 26, 2025
      If your TIC speakers aren't producing any sound, start by ensuring they're correctly connected to the cable. Then, verify that the speaker cable is properly connected to the receiver amplifier. Also, check that the receiver amplifier is powered on, not muted, has no headphones attached, and that the channels used for the exterior speakers (usually A or B) are active. Try using a different connection cable to your outdoor speakers or equipment.
  • P
    Paula DanielsAug 2, 2025
    What to do if one of my TIC TFS12 Speakers sounds distorted?
    • M
      Michael McclainAug 2, 2025
      To address distorted sound from one of your TIC speakers, follow the same steps you would take for a complete lack of sound. This involves checking the speaker connections, amplifier settings, and cable integrity to identify and resolve the source of the distortion.
  • M
    morrissylviaAug 10, 2025
    What to do if one of my TIC speakers has no sound?
    • S
      Sarah RothAug 10, 2025
      If you're only getting sound from one of your TIC speakers, begin by checking the balance control on your receiver speaker amplifier. Inspect all connections and the cable to the speaker that isn't working. You can also try swapping the cords from the working speaker to the non-working speaker connection to see if the problem lies with your receiver amplifier. Alternatively, remove the speaker cable at the working speaker and connect it directly to the non-working speaker to check the original speaker cable. If the speaker still doesn't work, the issue is likely with the speaker itself.
  • B
    brodriguezAug 16, 2025
    How to adjust treble or bass on TIC speakers?
    • K
      Kirk HowardAug 17, 2025
      To adjust the treble or bass on your TIC speakers, first check the tone settings on your receiver amplifier. You can then fine-tune the sound by adjusting the treble and bass settings. Also, make sure the connections from the amplifier to your speakers are correct, paying attention to polarity (+ to + and – to –). Poor sound replication can occur if speakers are out of polarity or phase.

Summary

Component List

Pre-Installation

Exterior Installation

Maintenance

Customer Service

Warranty Period

Installation Notes

Trouble Shooting

Technical Specifications

TIC TFS12 Specifications

General IconGeneral
BrandTIC
ModelTFS12
CategorySpeakers
LanguageEnglish

Related product manuals