EasyManua.ls Logo

Toro 74960 - User Manual

Toro 74960
76 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
FormNo.3413-627RevC
ZMaster
®
Professional6000
SeriesRidingMower
with60inor72inTURBOFORCE
®
Side
DischargeMower
ModelNo.74960—SerialNo.400000000andUp
ModelNo.74961—SerialNo.400000000andUp
Registeratwww.Toro.com.
OriginalInstructions(EN)
*3413-627*C

Table of Contents

Questions and Answers

  • J
    John BallardSep 15, 2025
    What causes the clutch to not engage on my Toro Lawn Mower?
    • W
      williamsjeffSep 15, 2025
      If the clutch on your Toro lawn mower won't engage, it could be due to a blown fuse, so replace the fuse. Check for low voltage supply at the clutch, and inspect the coil resistance, battery charge, charging system, and wiring connections, replacing if necessary. Also, inadequate current supply can be a factor; repair or replace the clutch lead wire or electrical system and clean connector contacts. Finally, if the rotor/armature airgap is too large, remove a shim or replace the clutch.
  • T
    Tyrone RodriguezSep 12, 2025
    What to do if my Toro Lawn Mower does not drive?
    • A
      ann58Sep 12, 2025
      If your Toro Lawn Mower doesn't drive, first check that the bypass valves are closed tight. If not, tighten them. Also, inspect the pump belt for wear, looseness, or breakage and change the belt if needed. Ensure the pump belt is correctly positioned on the pulley. Replace the spring if the idler spring is broken or missing. Finally, verify the hydraulic fluid level; add hydraulic fluid to the reservoirs if it is low, or let it cool down if it is too hot.
  • J
    jonesveronicaSep 9, 2025
    What to do if my Toro Lawn Mower pulls left or right?
    • M
      madison07Sep 9, 2025
      If your Toro Lawn Mower pulls to the left or right (with levers fully forward), it could be due to: * The tracking needs adjustment; adjust the tracking. * Incorrect tire pressure in drive tires; adjust tire pressure in the drive tires.
  • R
    Rebekah WoodAug 30, 2025
    How to fix uneven cutting height on Toro 74960?
    • L
      Lori DennisAug 30, 2025
      To fix an uneven cutting height on your Toro Lawn Mower, start by sharpening any dull blades or installing new ones if bent. Ensure the mower deck is level from side-to-side and front-to-rear. Clean the underside of the mower deck, adjust the tire pressure to the correct level. For a bent blade spindle, contact an Authorized Service Dealer.
  • K
    Kristin GriffithAug 30, 2025
    Why is my Toro 74960 Lawn Mower resulting in uneven cutting height?
    • G
      gbaileyAug 30, 2025
      If your Toro Lawn Mower is mowing with an uneven cutting height, several factors could be responsible. Ensure the blades are sharp; if not, sharpen them. Bent cutting blades can also cause this, so install new ones. Check if the mower deck is level from side-to-side and front-to-rear, and adjust as needed. A dirty underside of the mower can interfere with cutting, so clean it. Also, verify that the tire pressure is correct. For a bent blade spindle, contact an Authorized Service Dealer.
  • B
    Bradley SimmonsAug 30, 2025
    Why does the engine lose power in my Toro 74960?
    • N
      Natalie BanksAug 30, 2025
      If your Toro Lawn Mower engine loses power, try the following: Reduce the ground speed. Clean the air cleaner element. Add oil to the crankcase. Remove any obstruction from the cooling fins and air passages. Clean or replace the fuel cap. Replace the fuel filter. If the problem continues, it is recommended to contact an Authorized Service Dealer.
  • D
    David BassAug 31, 2025
    What to do if my Toro 74960 Lawn Mower is resulting in uneven cutting height?
    • K
      Kristine Williams MDAug 31, 2025
      If mowing with your Toro Lawn Mower results in an uneven cutting height, try the following: * Sharpen the blade(s). * Install new cutting blade(s). * Level the mower deck from side-to-side and front-to-rear. * Clean the underside of the mower. * Adjust the tire pressure.
  • A
    acostabrianSep 22, 2025
    Why does the starter not crank on my Toro 74960 Lawn Mower?
    • U
      uhesterSep 22, 2025
      If the starter on your Toro Lawn Mower does not crank, ensure that the blade control switch (PTO) is disengaged. Also, set the parking brake, ensure that the drive levers are in the neutral lock position, and sit on the seat. You may also need to charge the battery, check the electrical connections for good contact, or replace the fuse. If problems persist, contact an Authorized Service Dealer.
  • A
    andrewjimenezSep 23, 2025
    What to do if my Toro 74960 has abnormal vibration?
    • A
      amber84Sep 23, 2025
      If your Toro Lawn Mower is vibrating abnormally, several issues could be the cause: * The cutting blade(s) might be bent or unbalanced, so install new cutting blade(s). * The blade mounting bolt might be loose, so tighten it. * The engine mounting bolts could be loose, so tighten them. * A loose engine pulley, idler pulley, or blade pulley could be the problem, so tighten the appropriate pulley.
  • C
    Christopher JohnsonSep 12, 2025
    What causes the blades to not rotate on my Toro Lawn Mower?
    • T
      theresa21Sep 12, 2025
      If the blades on your Toro Lawn Mower do not rotate, it could be due to a damaged, worn, loose, or broken mower deck belt; install a new deck belt. Ensure the mower deck belt is properly installed on the deck pulley, checking the idler pulley, idler arm, and spring for correct position and function. Also, a worn, loose, or broken pump drive belt can cause this issue, so check the belt tension or install a new belt. Finally, check the idler spring and replace it if it is broken or missing.

Toro 74960 Specifications

General IconGeneral
BrandToro
Model74960
CategoryLawn Mower
LanguageEnglish

Related product manuals