To Next PageTo Next PageWhat to do if my Toro Flex-Force Power System 51830 does not run or runs continuously?
If your Toro Trimmer is not running or runs continuously, the battery pack leads might have moisture on them. Allow the battery pack to dry or wipe it dry. Also, ensure the battery is fully installed into the tool by removing and replacing it, making sure it's fully installed and latched.
How to fix a Toro Flex-Force Power System 51830 that won't start?
If your Toro Trimmer isn't starting, here are a few things to check: * Ensure the battery is fully installed and latched into the tool. Remove and replace it to be sure. * Make sure the battery pack is charged. If not, remove it and charge it. * The battery pack may be damaged. If so, replace it.
What to do if the LED indicator light on the Toro Trimmer battery charger is blinking red?
If the LED indicator light on your battery charger is blinking red, there may be an error in communication between the battery and the charger, or the battery pack may be weak. Try removing the battery, unplugging the charger for 10 seconds, and then plugging it back in and reattaching the battery. If the light continues to blink red after two attempts, properly dispose of the battery at a recycling facility.
Why is my Toro Trimmer not reaching full power?
If the Toro Trimmer does not reach full power, the battery pack charge capacity might be too low, so remove the battery pack from the tool and fully charge it. Alternatively, the air vents could be blocked, so try cleaning the air vents.
Why is the LED indicator light on my Toro Flex-Force Power System 51830 battery charger red?
If the LED indicator light on the battery charger is red, the charger or battery pack may be outside the correct temperature range. Unplug the charger and move both the charger and battery pack to a dry place where the temperature is between 5°C (41°F) and 40°C (104°F).
Why is my Toro Flex-Force Power System 51830 producing excessive vibration or noise?
If the Toro Trimmer is producing excessive vibration or noise, check for debris on the drum area and clean it off. Also, the spool might not be wound correctly; try advancing the line using the trigger switch and/or remove the line and wind the spool again.
What to do if the Toro Trimmer battery charger is not working?
If the battery charger isn't working, it might be outside the correct temperature range. Unplug it and move it to a dry place where the temperature is between 5°C (41°F) and 40°C (104°F). Also, the outlet the charger is plugged into might not have power; contact a licensed electrician to repair the outlet.
Why does the battery pack on my Toro Flex-Force Power System 51830 Trimmer lose charge quickly?
If the battery pack loses charge quickly, it may be outside the correct temperature range. Move the battery pack to a place where it is dry and the temperature is between 5°C (41°F) and 40°C (104°F).
General| Battery Voltage | 60V |
|---|---|
| Battery Type | Lithium-Ion |
| Power Source | Battery |
| Battery Runtime | Up to 45 minutes |
| Charging Time | 60 minutes |
| Line Diameter | 0.080 inches |
Ensures operator is trained and responsible for safe appliance operation.
Covers keeping bystanders away and using correct equipment for safety.
Details proper use, lighting, and avoiding hazards during operation.
Guidelines for product care, cleaning, and safe storage.
Information on battery charge status, recycling program, and charger details.
Decals providing operational warnings, safety symbols, and product identification.
List of parts shipped with the product for initial verification.
Instructions for optionally mounting the battery charger securely.
Procedure for unfolding and securing the trimmer's handle shafts.
Steps for attaching the auxiliary handle to the trimmer.
Procedure for securing the guard onto the trimmer base.
Details model, rated voltage, charger and battery types.
Specifies ideal temperatures for charging and using the trimmer.
Procedure for powering on the trimmer, including trigger use.
How to safely turn off the trimmer by releasing triggers.
Steps to detach the battery pack from the trimmer.
Guide to inserting the battery into the charger and understanding indicators.
Methods for advancing the cutting line using bump feed or manually.
How to change cutting width and best practices for efficient trimming.
Cleaning and checking fasteners after each use.
Instructions for replacing the trimmer line spool and string.
Guidelines for storing the tool, battery, and charger safely.
Steps for preparing the battery pack for recycling.
