Toro GrandStand 74567TE User Manual (English)

Questions and Answers:

M
Michael DorseyJul 31, 2025
Why won't my Toro GrandStand 74567TE Lawn Mower engine start?
- B
  Barbara ReedJul 31, 2025
  There are several reasons why your Toro Lawn Mower engine might not start. It could be due to an empty fuel tank, so fill it with gasoline. The choke might not be on; move the choke lever to the choke position. A loose or disconnected spark plug wire can also be the culprit; install the wire on the spark plug. Other potential causes include a pitted, fouled, or incorrectly gapped spark plug (install a new one), a dirty air cleaner (service the air cleaner element), or dirt in the fuel filter (replace the fuel filter).
S
Sara ThompsonAug 4, 2025
What to do if my Toro GrandStand 74567TE engine loses power?
- D
  Derek GlennAug 4, 2025
  If your Toro Lawn Mower engine is losing power, several factors could be responsible. First, the engine load may be excessive, so reduce the ground speed. A dirty air cleaner can also cause power loss; service the air cleaner. Check the oil level in the crankcase and add oil if it's low. Also, make sure the cooling fins and air passages under the engine blower housing aren't plugged; remove any obstructions. A faulty spark plug or a plugged fuel cap vent hole can also contribute to power loss; replace the spark plug or clean/replace the fuel cap, respectively. Finally, a dirty fuel filter can cause the engine to lose power, so replace the fuel filter.
E
Elizabeth ByrdAug 8, 2025
What to do if Toro Lawn Mower blades do not rotate?
- W
  William Osborne MDAug 8, 2025
  If the blades on your Toro Lawn Mower aren't rotating, start by checking the pump drive belt tension. If the belt is worn, loose, or broken, check the belt tension. If the pump drive belt is off the pulley, install the drive belt and check the adjusting shafts and belt guides for correct position. Also, inspect the mower deck belt for wear, looseness, or breakage and replace it if necessary. If the mower deck belt is off the pulley, install the deck pulley and check the idler pulley, idler arm, and spring for correct position and function. Replace any broken or missing idler springs. Finally, adjust the clutch air gap.
A
andersonkevinAug 13, 2025
Why does my Toro Lawn Mower have an uneven cutting height?
- R
  ramoslanceAug 13, 2025
  Uneven cutting height with your Toro Lawn Mower can be attributed to several factors. Dull blades are a common cause; sharpen them. Bent cutting blades can also lead to this issue, so replace them. Ensure the mower deck is level from side to side and adjust if necessary. Correct the mower deck's front-to-rear pitch. A dirty underside of the mower deck can interfere with cutting, so clean it. Incorrect tire pressure can also cause uneven cutting, so adjust the tire pressure.
M
Michael MillerAug 17, 2025
What to do if my Toro GrandStand 74567TE Lawn Mower does not drive?
- D
  davidsnowAug 17, 2025
  If your Toro Lawn Mower isn't driving, start by checking the hydraulic oil reservoir and add hydraulic oil if the level is low. If there is air in the hydraulic system, bleed the air out. Inspect the pump drive belt for slipping and replace it if needed. Also, check for a missing pump drive belt idler spring and replace it if necessary. Finally, make sure the pump by-pass valves are not open and tighten them if they are.
K
Kathleen RamirezAug 21, 2025
Why is my Toro GrandStand 74567TE Lawn Mower engine overheating?
- V
  vegadavidAug 22, 2025
  Your Toro Lawn Mower engine might be overheating due to a few reasons. The engine load could be too high, so try reducing the ground speed. Another cause could be a low oil level in the crankcase, so add oil. Also, check the cooling fins and air passages under the engine blower housing for obstructions and remove them.
W
williamsaprilAug 26, 2025
How to fix abnormal vibration in my Toro Lawn Mower?
- A
  Anna MartinezAug 26, 2025
  Abnormal vibration in your Toro Lawn Mower can stem from several issues. Check the cutting blades for bending or imbalance and replace them if needed. Ensure the blade mounting bolt is tightened securely. Also, inspect the engine mounting bolts and tighten them if they are loose. Similarly, check for any loose engine pulley, idler pulley, or blade pulley, and tighten the appropriate pulley.