Toro TimeCutter MX5060

Questions and Answers

E
eedwardsJul 26, 2025
Why won't my Toro Lawn Mower engine start?
- A
  alexandrajoyceJul 26, 2025
  Several factors can prevent your Toro Lawn Mower engine from starting. First, ensure the fuel tank isn't empty by filling it. If it is not the reason, make sure the choke is on. A dirty air cleaner can also be the culprit, so clean or replace it. Check that the spark plug wire(s) is securely connected to the spark plug. Inspect the spark plug(s) for damage, and replace if needed. Additionally, ensure the fuel filter is clean, and the fuel tank contains the correct type of fuel. Finally, check that the oil level in the crankcase is sufficient and add oil if needed.
M
mosesjessicaJul 30, 2025
Why does my Toro Lawn Mower engine lose power?
- R
  Richard MullinsJul 31, 2025
  If your Toro Lawn Mower engine is losing power, consider these possible causes: The engine load might be excessive, so reduce ground speed. A dirty air cleaner can also cause power loss, so clean the air cleaner element. Check the oil level in the crankcase and add oil if it's low. Make sure the cooling fins and air passages under the engine blower housing are free from obstructions. Inspect the spark plug(s) and replace them if pitted, fouled, or incorrectly gapped. Finally, if there is incorrect fuel in the fuel tank, drain the tank and replace the fuel with the proper type.
T
Tom WestAug 4, 2025
What to do if my Toro TimeCutter MX5060 starter does not crank?
- K
  Kathleen DayAug 4, 2025
  If the starter on your Toro Lawn Mower isn't cranking, try these steps: Ensure the blade control switch is disengaged. Verify that the motion control levers are in the park position. If the battery is dead, charge it. Check the electrical connections for corrosion or looseness, ensuring good contact. Finally, inspect the fuse and replace it if blown.
M
Michael Mendoza DVMAug 8, 2025
How to fix uneven cutting height on Toro TimeCutter MX5060 Lawn Mower?
- M
  Michael FigueroaAug 8, 2025
  To correct uneven cutting height on your Toro Lawn Mower, consider these factors: Sharpen the blade(s) if they are not sharp. Replace any bent cutting blade(s). Level the mower from side-to-side and front-to-rear. Adjust the anti-scalp wheel height if it's not set correctly. Clean the underside of the mower if it's dirty. Adjust the tire pressure to the correct level.
A
Amanda DaughertyAug 12, 2025
What to do if the blades on my Toro Lawn Mower do not rotate?
- S
  summer58Aug 12, 2025
  If the blades on your Toro Lawn Mower aren't rotating, check if the drive belt is worn, loose, or broken, and install a new drive belt if necessary. Also, ensure the drive belt is properly positioned on the pulley, and check the adjusting shafts and belt guides for correct positioning. Finally, check if the mower belt is worn, loose, or broken and install a new mower belt if needed.
D
Dwayne JohnsonAug 16, 2025
How to fix Toro TimeCutter MX5060 Lawn Mower when the engine overheats?
- J
  Jeff CookAug 16, 2025
  If your Toro Lawn Mower's engine is overheating, there are several potential causes. First, reduce ground speed if the engine load is excessive. Check the oil level in the crankcase and add oil if it's low. Inspect the cooling fins and air passages under the engine blower housing for obstructions and remove them. Also, make sure that the air cleaner is not dirty; clean or replace the air cleaner element if necessary.
M
Martin WilliamsAug 21, 2025
How to stop abnormal vibration in my Toro TimeCutter MX5060 Lawn Mower?
- T
  Thomas CochranAug 21, 2025
  To address abnormal vibration in your Toro Lawn Mower, check the following: Tighten any loose engine mounting bolts. Ensure the engine pulley, idler pulley, or blade pulley are tightened appropriately. Replace the cutting blade(s) if they are bent or unbalanced. Also, tighten any loose blade mounting bolts.

Summary

Introduction

CALIFORNIA Proposition 65 Warning

Warning regarding chemicals in the product known to cause cancer or reproductive harm.

Safety

Safe Operating Practices

Essential safety rules for operating the mower to prevent injury or death.

General Operation

Guidelines for safe and proper operation of the mower in various conditions.

Slope Operation

Specific safety precautions and techniques for operating the mower on slopes.

Children

Safety warnings regarding the presence and interaction of children with the mower.

Towing Safety

Safety guidelines for towing equipment with the mower.

Toro Riding Mower Safety

Specific safety information for Toro riding mower products.

Service

Safe Handling of Gasoline

Precautions for safe handling of gasoline to prevent fire and explosion.

General Service

General maintenance and safety guidelines for servicing the machine.

Slope Indicator

Safety and Instructional Decals

Battery Symbols

Product Overview

Controls

Familiarize yourself with all machine controls before starting the engine and operating.

Motion Control Levers and Parking Brake Position

Details on operating the independent wheel motors and engaging the parking brake.

Smart Speed Control System Lever

Explanation of the lever for selecting between high and low speed ranges.

Height-of-Cut Lever

How to adjust the mower deck height from the operator's seat.

Hour Meter

Information on the hour meter that records operating time.

Fuel Window

Location and use of the fuel window to check gasoline levels.

Operation

Think Safety First

Critical safety guidelines and practices for operating the mower safely.

Fuel Safety

Essential safety precautions when handling gasoline to prevent fire and explosion.

Before Starting

Recommended Fuel

Specifications for the correct type of unleaded gasoline to use for optimal performance.

Using Stabilizer;Conditioner

Benefits and instructions for using fuel stabilizer to maintain fuel freshness.

Checking the Engine Oil Level

Procedure for checking the engine oil level before operation.

Filling the Fuel Tank

Instructions on how to safely and correctly fill the fuel tank.

Starting the Engine

Operating the Blades

Engaging the Blades

Steps to safely engage the mower blades for operation.

Disengaging the Blades

Procedure for safely disengaging the mower blades.

Testing the Safety Interlock System

Stopping the Engine

Steps to properly stop the engine and secure the machine.

Using the Smart Speed Control System

How to use the Smart Speed™ Control System for variable speed operation.

Driving

Forward

Instructions for operating the machine in the forward direction.

Backward

Instructions for operating the machine in reverse.

Stopping the Machine

Procedure for stopping the mower safely.

Adjusting the Height of Cut

Adjusting the Anti-Scalp Rollers

Instructions for adjusting the anti-scalp rollers for proper deck height.

Positioning the Seat

Adjusting the Motion Control Levers

How to adjust the height of the motion control levers for operator comfort.

Adjusting the Tilt

Pushing the Machine by Hand

To Operate the Machine

Procedure to disengage the electric brake and prepare the machine for operation after manual pushing.

Grass Deflector

Operating Tips

Guidance on mower operation, including speed control, cutting advice, and blade maintenance.

Keep the Underside of the Mower Clean

Importance of cleaning the mower deck underside after each use to prevent buildup.

Maintenance

Recommended Maintenance Schedule(s)

Schedule of maintenance tasks based on service intervals.

Premaintenance Procedures

Raising the Seat

Steps to raise the seat to access various components for maintenance.

Lubrication

Greasing the Bearings

Procedure and interval for greasing lubrication points.

Engine Maintenance

Servicing the Air Cleaner

Instructions for cleaning or replacing the air cleaner element.

Servicing the Engine Oil

Details on oil type, capacity, and viscosity for engine lubrication.

Checking the Engine Oil Level

Procedure for checking the engine oil level before each use.

Changing the Engine Oil

Procedure for Changing Engine Oil

Step-by-step instructions for draining and refilling the engine oil.

Changing the Engine Oil Filter

Servicing the Spark Plug

Instructions for checking and replacing the spark plug.

Installing the Spark Plug

Cleaning the Cooling System

Fuel System Maintenance

Replacing the In-line Fuel Filter

Procedure for replacing the in-line fuel filter at specified intervals.

Electrical System Maintenance

Removing the Battery

Steps for safely removing the battery from the machine.

Charging the Battery

Instructions for charging the battery and disconnecting it.

Servicing the Fuses

Installing the Battery

Drive System Maintenance

Checking the Tire Pressure

Procedure for checking and maintaining proper tire pressure.

Releasing the Electric Brake

Instructions for manually releasing the electric brake.

Hydraulic System Maintenance

Checking the Hydraulic Oil Level

Procedure for checking and adding hydraulic oil to the expansion reservoir.

Removing Hydraulic System Filters

Steps for safely removing hydraulic system filters.

Changing the Hydraulic System Oil and Filters

Procedure for changing hydraulic oil and filters, including bleeding the system.

Installing the Hydraulic System Filters

Procedure for Installing Hydraulic Filters

Steps for installing new hydraulic filters and adding oil.

Bleeding the Hydraulic System

Mower Maintenance

Servicing the Cutting Blades

Guidance on maintaining sharp blades for optimal cutting and lawn health.

Checking for Bent Blades

Procedure for Checking Bent Blades

Method for checking mower blades for bends or damage.

Sharpening the Blades

Removing the Blades

Steps for safely removing mower blades for replacement or sharpening.

Installing the Blades

Procedure for installing mower blades correctly.

Leveling the Mower Deck

Leveling the Mower from Side-to-Side

Procedure for ensuring the mower deck is level side-to-side.

Adjusting the Front-to-Rear Blade Slope

Instructions for adjusting the front-to-rear slope of the mower blades.

Removing the Mower

Procedure for Removing the Mower Deck

Steps to detach the mower deck from the machine for service or storage.

Mower Belt Maintenance

Inspecting the Belts

Procedure for inspecting mower belts for wear and damage.

Replacing the Mower Belt

Steps for replacing the mower belt.

Installing the Mower

Procedure for installing the mower deck onto the machine.

Replacing the Grass Deflector

Procedure for Replacing Grass Deflector

Steps for replacing a damaged or worn grass deflector.

Cleaning

Washing the Underside of the Mower

Instructions for washing the underside of the mower deck after use.

Storage

Cleaning and Storage

Procedures for cleaning and preparing the machine for storage.

Troubleshooting

The engine overheats

Possible causes and corrective actions for engine overheating.

The starter does not crank

Possible causes and corrective actions when the starter motor does not engage.

The engine will not start, starts hard, or fails to keep running

Troubleshooting steps for engine starting and running issues.

The engine loses power

Possible causes and corrective actions for a loss of engine power.

The machine does not drive

Troubleshooting steps when the machine fails to move.

There is abnormal vibration

Possible causes and corrective actions for abnormal machine vibration.

Uneven cutting height

Troubleshooting steps for uneven lawn cutting height.

The blades do not rotate

Possible causes and corrective actions when mower blades fail to rotate.

Schematics

Toro TimeCutter MX5060 Specifications

General

Engine Power	24.5 HP
Cutting Width	50 inches
Cutting Height	1.5 - 4.5 inches
Transmission	Hydrostatic
Deck Material	10-gauge steel
Blade Engagement	Electric PTO
Spindle Material	Aluminum
Warranty	3-year limited
Fuel Capacity	3 gallons