Toro TITAN HD 74467 - User Manual

Questions and Answers

S
Selena HeathAug 19, 2025
Why is my Toro TITAN HD 74467 Lawn Mower engine overheating?
- J
  Joel MillsAug 19, 2025
  If your Toro Lawn Mower engine overheats, it might be due to several reasons. The engine load could be excessive, so try reducing the ground speed. Also, check if the oil level in the crankcase is low and add oil if needed. Obstructions in the cooling fins and air passages can also cause overheating, so remove any obstructions. Another possible cause is a dirty air cleaner, in which case you should clean or replace the air-cleaner element. If the issue persists, there might be dirt, water, or stale fuel in the fuel system, and you should contact an Authorized Service Dealer.
N
Nicole BoyleAug 22, 2025
What to do if my Toro Lawn Mower starter does not crank?
- H
  Heather EnglishAug 22, 2025
  If your Toro Lawn Mower starter doesn't crank, first ensure the blade-control switch is disengaged. Next, make sure the motion-control levers are in the NEUTRAL-LOCK position. If it still doesn't crank, the battery might be dead, so charge it. Check the electrical connections for good contact if they are corroded or loose. Also, inspect the fuse and replace it if it's blown. If none of these steps work, a relay or switch might be damaged, and you should contact an Authorized Service Dealer.
C
Christina PerezAug 25, 2025
Why does my Toro Lawn Mower engine lose power?
- M
  Michele Wilson MDAug 26, 2025
  If your Toro Lawn Mower engine loses power, first ensure that the engine load is not excessive by reducing the ground speed. Check the air cleaner for dirt and clean it if necessary. Verify that the oil level in the crankcase is adequate; add oil if it's low. Also, inspect the cooling fins and air passages for any obstructions and remove them. Check the fuel cap; if the vent hole is plugged, clean or replace it. If there is dirt in the fuel filter, replace it. If the problem persists, there may be dirt, water, or stale fuel in the fuel system, and you should contact an Authorized Service Dealer.
J
Juan WilsonAug 28, 2025
Why is my Toro Lawn Mower vibrating so much?
- J
  Juan ReynoldsAug 28, 2025
  If your Toro Lawn Mower machine vibrates abnormally, the cutting blades might be bent or unbalanced, so install new ones. Ensure the blade mounting bolt is tight. Check the engine mounting bolts and tighten them if they are loose. Also, inspect the engine pulley, idler pulley, or blade pulley for looseness and tighten the appropriate pulley. If the engine pulley is damaged or the blade spindle is bent, or the motor mount is loose or worn, you should contact an Authorized Service Dealer.
T
Thomas MatthewsAug 30, 2025
What to do if my Toro TITAN HD 74467 does not drive?
- B
  bmurrayAug 31, 2025
  If your Toro Lawn Mower does not drive, make sure the bypass valves are closed tight by tightening them. If the pump belt is worn, loose, or broken, or if the pump belt is off a pulley, change the belt. If the idler spring is broken or missing, replace the spring. Check the hydraulic fluid level; if it's low, add hydraulic fluid to the reservoirs, or let it cool down if it is too hot.
D
dawsonterriSep 3, 2025
Why is the clutch not engaging on my Toro TITAN HD 74467 Lawn Mower?
- K
  Kelsey TorresSep 3, 2025
  If your Toro Lawn Mower clutch does not engage, replace the fuse. Check the coil resistance, battery charge, charging system, and wiring connections, and replace components if necessary. Check the coil resistance, battery charge, charging system, and wiring connections and replace parts if necessary if there is low voltage supply at the clutch. If the coil is damaged, replace the clutch. If there is inadequate current supply, repair or replace the clutch lead wire or electrical system and clean the connector contacts. If the rotor/armature air gap is too large, remove the shim or replace the clutch.
J
James BlairSep 5, 2025
How to fix uneven cutting height on my Toro TITAN HD 74467?
- D
  dickersonashleySep 5, 2025
  If the cutting height of your Toro Lawn Mower is uneven, start by sharpening the blades. If a cutting blade is bent, install a new one. Ensure the mower is level from side-to-side and front-to-rear. If applicable, adjust the anti-scalp wheel height. Clean the underside of the mower deck. Adjust the tire pressure. If a blade spindle is bent, you should contact an Authorized Service Dealer.
O
Olivia JohnsonSep 8, 2025
Why does my Toro Lawn Mower pull to one side?
- T
  Theresa VargasSep 8, 2025
  If your Toro Lawn Mower pulls to the left or right (with levers fully forward), you may need to adjust the tracking. Also, ensure the tire pressure in the drive tires is correct by adjusting it.
T
Thomas MontgomerySep 12, 2025
Why are the blades not rotating on my Toro Lawn Mower?
- V
  Virginia MerrittSep 12, 2025
  If the blades on your Toro Lawn Mower do not rotate, install a new drive belt if the current one is worn, loose, or broken. If the drive belt is off of the pulley, reinstall the drive belt and check the adjusting shafts and belt guides for the correct position. If the power takeoff (PTO) switch or PTO clutch is faulty, or if the mower belt is worn, loose, or broken, you should contact an Authorized Service Dealer for the PTO switch/clutch, or install a new mower belt.
K
Kevin WilliamsNov 15, 2025
Why won't my Toro TITAN HD 74467 engine start?
- M
  Monique ReedNov 15, 2025
  If your Toro Lawn Mower engine doesn't start, starts hard, or fails to keep running, the fuel tank might be empty, so fill it up. Ensure the fuel-shutoff valve is open. Check the oil level in the crankcase and add oil if needed. Make sure the throttle is positioned midway between the slow and fast settings. If there's dirt in the fuel filter, replace it. If these steps don't resolve the issue, there may be dirt, water, or stale fuel in the fuel system, a dirty air cleaner, a malfunctioning seat switch, corroded or damaged electrical connections, a worn or damaged relay or switch, a fouled or improperly gapped spark plug, or a disconnected spark-plug wire. For the fuel system, relay/switch, you should contact an Authorized Service Dealer. Clean or replace the air-cleaner element. Check the ...

Summary

Safety

Slope Indicator

Product Overview and Controls

Operation: Before Operation

Fuel Safety

Safety guidelines for handling fuel to prevent fire and explosion.

Adding Fuel

Using the Rollover-Protection System (ROPS)

Lowering the Roll Bar

Using the Safety-Interlock System

Understanding the Safety-Interlock System

Raising the Roll Bar

Testing the Safety-Interlock System

During Operation Safety

General Safety

General safety precautions during machine operation.

Rollover Protection System (ROPS) Safety

Slope Safety

Operating the Parking Brake

Operating the Mower Blade-Control Switch (PTO)

Starting and Shutting Off the Engine

Starting the Engine

Using the Motion-Control Levers

Adjusting the Height of Cut

After Operation

After Operation Safety

Safety precautions to follow after operating the machine.

Using the Drive-Wheel Release Valves

Transporting the Machine

Loading the Machine

Maintenance

Recommended Maintenance Schedule(s)

Schedule of maintenance tasks based on service intervals.

Pre-Maintenance Procedures

Maintenance Safety

Safety precautions to take before performing maintenance.

Lubrication

Greasing the Machine

Engine Maintenance

Engine Safety

Safety precautions specific to engine maintenance.

Servicing a Kawasaki Engine

Maintenance procedures for Kawasaki engines.

Servicing the Air Cleaner

Servicing the Engine Oil

Engine-Oil Specifications

Checking the Engine-Oil Level

Procedure for checking the engine oil level.

Changing the Engine Oil and Oil Filter

Changing the Engine-Oil Filter

Servicing the Spark Plug

Removing the Spark Plug

Servicing a Kohler Engine

Servicing the Paper Element

Servicing a Toro Engine

Servicing the Air Cleaner

Air cleaner maintenance for Toro engines with standard air cleaner.

Installing the Air Cleaner

Servicing the Air Cleaner

Engines with a Heavy-Duty Air Cleaner

Air cleaner maintenance for Toro engines with heavy-duty air cleaner.

Changing the Engine-oil filter

Checking the Spark Arrester

Fuel System Maintenance

Replacing the Fuel Filter

Electrical System Maintenance

Electrical System Safety

Safety precautions for electrical system work.

Servicing the Battery

Procedures for battery maintenance and removal.

Installing the Battery

Drive System Maintenance

Cooling System Maintenance

Brake Maintenance

Adjusting the Parking Brake

Belt Maintenance

Replacing the Mower Belt for Side-Discharge Mower Decks

Replacing the Mower Belt for Rear-Discharge Mower Decks

Replacing the Counter-Rotating Belt

Replacing the Hydraulic Pump-Drive Belt

Hydraulic System Maintenance

Hydraulic System Safety

Safety precautions when working with hydraulic systems.

Servicing the Hydraulic System

Checking the Hydraulic Fluid Level

Procedure to check the hydraulic fluid level.

Changing the Hydraulic-System Filters and Fluid

Procedure to change hydraulic system filters and fluid.

Installing the Hydraulic-System Filters

Mower Deck Maintenance

Servicing the Cutting Blades

Instructions for servicing and maintaining mower blades.

Blade Safety

Safety warnings related to mower blades.

Inspecting the Blades

Checking for Bent Blades

Replacing the Blades for Side Discharge Mower Decks

Replacing the Blades for Rear Discharge Mower Decks

Installing the Blades for Rear Discharge Mower Decks

Sharpening the Blades

Leveling the Mower Deck

Adjusting the Side-to-Side Leveling and the Blade Slope

Removing the Mower Deck

Cleaning

Storage

Storage Safety

Cleaning and Storage

Troubleshooting

The engine overheats

Troubleshooting steps for engine overheating issues.

The starter does not crank

Troubleshooting steps when the starter motor does not engage.

The engine does not start, starts hard, or fails to keep running

Troubleshooting steps for engine starting and running issues.

The engine loses power

Troubleshooting steps for engine power loss.

Schematics

Wire Diagram-Toro Engines (Rev. A)

Toro TITAN HD 74467 Specifications

General

Cutting Width	60 inches
Transmission	Hydrostatic
Spindle Material	Cast aluminum
Ground Speed (Forward)	10 mph
Starting System	Electric
Mulching Capability	Yes
Bagging Capability	Optional
Side Discharge Capability	Yes
Blade Tip Speed	18, 500 ft/min
Tires (Front)	13 x 6.5-6
Tires (Rear)	24 x 12-12
Cutting Height	1.5 - 5 inches
Deck Material	7-gauge steel