Toro Wheel Horse XL 380H User Manual (English)

Questions and Answers:

P
Philip Allen MDAug 17, 2025
Why won't my Toro Lawn Mower engine start?
- E
  Erin PetersonAug 17, 2025
  If your Toro Lawn Mower's engine won't start, starts hard, or fails to keep running, try the following: Make sure you are sitting on the seat. Fill the fuel tank with gasoline. Clean or replace the air cleaner element. Connect the wire to the spark plug. Install a new, correctly gapped spark plug. Adjust the throttle cable. Replace the fuel filter. Adjust the carburetor idle speed and idle mixture.
K
Katie MorrisAug 20, 2025
Why is my Toro Wheel Horse XL 380H Lawn Mower engine losing power?
- J
  Jose WilliamsAug 20, 2025
  If your Toro Lawn Mower engine loses power, try the following: Reduce ground speed. Clean the air cleaner element. Add oil to the crankcase. Remove any obstructions from the cooling fins and air passages. Install a new, correctly gapped spark plug. Clean or replace the fuel cap. Replace the fuel filter.
A
Amanda GonzalezAug 22, 2025
What to do if the blades do not rotate on my Toro Wheel Horse XL 380H Lawn Mower?
- S
  Steven PooleAug 22, 2025
  If the blades on your Toro Lawn Mower do not rotate, try the following: Install a new blade drive belt. Install the blade drive belt and check the idler pulley and belt guides for the correct position.
M
Melissa DayAug 25, 2025
Why is the cutting height uneven on my Toro Lawn Mower?
- B
  Brianna LaneAug 26, 2025
  Uneven cutting height with your Toro Lawn Mower can be caused by a few factors. First, check and set the tire pressure to the correct level. Ensure the mower is level from side-to-side and front-to-rear. Also, clean the underside of the mower to remove any accumulated dirt.
A
Alfred JohnsonAug 28, 2025
What to do if the blades on my Toro Lawn Mower do not rotate?
- S
  Shirley MarksAug 28, 2025
  If the blades on your Toro Lawn Mower are not rotating, it could be due to the blade drive belt. Inspect the belt to see if it is worn, loose, or broken; if so, install a new blade drive belt. Also, check if the blade drive belt is off of the pulley and install it correctly, ensuring the idler pulley and belt guides are in the correct position.
A
Ana RiosAug 30, 2025
What to do if my Toro Lawn Mower starter does not crank?
- J
  johnathanmeyerAug 30, 2025
  If the starter on your Toro Lawn Mower does not crank, try the following: Disengage the blade control (PTO). Set the parking brake. Charge the battery. Check the electrical connections for good contact. Replace the fuse.
P
Pamela HarperSep 2, 2025
Why is my Toro Wheel Horse XL 380H Lawn Mower engine overheating?
- O
  oscarmeyerSep 2, 2025
  If the engine in your Toro Lawn Mower overheats, try the following: Reduce the ground speed. Add oil to the crankcase. Remove any obstruction from the cooling fins and air passages.
N
Nancy BarkerSep 5, 2025
How to fix a Toro Wheel Horse XL 380H Lawn Mower that is cutting unevenly?
- A
  Arthur JordanSep 5, 2025
  If your Toro Lawn Mower is cutting unevenly, try these steps: Set the tire pressure. Level the mower from side-to-side and front-to-rear. Clean the underside of the mower.
R
Rachel HinesSep 8, 2025
Why is there an abnormal vibration in my Toro Lawn Mower?
- J
  Jason TapiaSep 8, 2025
  If there is an abnormal vibration in your Toro Lawn Mower, try the following: Install new blades. Tighten the blade mounting bolt. Tighten the engine mounting bolts. Tighten the appropriate pulley.
C
Catherine NormanSep 10, 2025
What causes my Toro Lawn Mower engine to overheat?
- K
  Keith BensonSep 10, 2025
  If your Toro Lawn Mower engine is overheating, there are a few things to check. First, the engine load might be excessive, so shift into a lower gear to reduce ground speed. Also, ensure that the oil level in the crankcase is adequate by adding oil if it's low. Finally, make sure the cooling fins and air passages under the engine blower housing are free from any obstructions.

Toro Wheel Horse XL 380H Specifications

General

Cutting Width	38 inches
Number of Blades	2
Transmission	Hydrostatic
Drive	Rear-wheel drive
Turning Radius	18 inches
Engine Type	4-cycle OHV
Cutting Height	1-4 inches
Deck Material	Steel