Toro Z Master Professional 7500-D Series - Raising and Locking the Wing Decks

To Next Page

To Previous Page

RaisingandLockingthe

WingDecks

1.Ensurethatallpersonsareclearofthedeck

wings.

2.Parkthemachineonalevelsurface,disengage

theblade-controlswitch,andengagetheparking

brake.

3.Pressandholdthetopofthedeck-control

switch;thecenterdeckwillraiserst,thenthe

wingdecks.

4.Shutofftheengine,removethekey,andwait

forallmovingpartstostopbeforeleavingthe

operatingposition.

5.Removetheclevispinandhairpincotterfrom

thestoragelocationandsecureeachwinginthe

uprightposition(Figure24andFigure25).

g363149

Figure24

1.Pinstoragelocation

g363150

Figure25

1.Clevispin

2.Hairpincotter

Main Page

Table of Contents4
Safety5
General Safety5
Slope Indicator6
Safety and Instructional Decals7
Product Overview13
Controls14
Horizon Display Monitor14
Specifications16
Attachments/Accessories16
Before Operation17
Before Operation Safety17
Adding Fuel18
Performing Daily Maintenance18
Breaking in a New Machine18
Using the Rollover Protection System (ROPS)19
Adjusting the Mirrors20
Using the Motion-Control Levers20
Checking the Safety-Interlock System21
Positioning the Seat25
Unlatching the Seat25
Changing the Seat Suspension25
During Operation26
During Operation Safety26
Lowering the Wing Decks28
Operating the Mower Blade-Control Switch (PTO)29
Ensure that All Persons Are Clear of the Deck Wings29
Starting the Engine30
Shutting off the Engine30
Raising and Locking the Wing Decks31
Driving the Machine32
Adjusting the Height of Cut33
Park the Machine on a Level Surface, Disengage33
The Blade-Control Switch, and Engage the Parking33
Adjusting the Anti-Scalp Rollers34
Operating with the Overheat Sensor35
Operating Tips35
After Operation36
After Operation Safety36
Using the Drive Train Brake Release36
Using the Wing Deck Fold Release Valve37
Transporting the Machine38
Maintenance40
Maintenance Safety40
Recommended Maintenance Schedule(S)40
Lubrication42
Greasing the Machine42
Lubricating the Drive U-Joints and Splined Slip Joint43
Greasing the Caster Pivots43
Greasing the Caster-Wheel Hubs44
Engine Maintenance45
Engine Safety45
Servicing the Air Cleaner45
Servicing the Engine Oil46
Inspecting the Engine-Valve Clearance47
Fuel System Maintenance48
Draining the Fuel Filter/Water Separator48
Replacing the Water Separator49
Checking the Fuel Lines and Connections49
Electrical System Maintenance50
Electrical System Safety50
Servicing the Battery50
Servicing the Fuses52
Drive System Maintenance53
Checking the Seat Belt53
Adjusting the Tracking53
Checking the Tire Pressure54
Checking the Wheel Lug Nuts54
Adjusting the Caster-Pivot Bearing54
Servicing the Gearbox55
Checking the Drive Wheel Gearbox Oil56
Changing the Drive Wheel Gearbox Oil56
Cooling System Maintenance57
Cooling System Safety57
Checking the Engine-Coolant Level57
Cleaning the Radiator and Engine-Hood Screen57
Changing the Engine Coolant58
Belt Maintenance59
Inspecting the Belts59
Replacing the Mower Belts59
Checking the Alternator-Belt Tension60
Controls System Maintenance61
Adjusting the Control-Handle Position61
Adjusting the Motion-Control Linkage61
Adjusting the Motion-Control Damper62
Hydraulic System Maintenance63
Hydraulic System Safety63
Servicing the Hydraulic System63
Mower Deck Maintenance65
Blade Safety65
Servicing the Cutting Blades65
Leveling the Mower Deck67
Checking the Wing Deck Bushings70
Changing the Wing Deck Bushings71
Press and Hold the Top of the Deck-Control71
Switch; the Center Deck will Raise First, then the71
Wing Decks71
Shut off the Engine, Remove the Key, and Wait for All Moving Parts to Stop before Leaving the Operating Position71
Cleaning73
Cleaning the Engine and Exhaust System Area73
Cleaning the Machine and Mower Deck73
Disposing of Waste73
Storage74
Storage Safety74
Cleaning and Storing the Machine74
Troubleshooting75
Schematics77

Toro Z Master Professional 7500-D Series - Raising and Locking the Wing Decks

Table of Contents

Other manuals for Toro Z Master Professional 7500-D Series

Related product manuals