EasyManua.ls Logo

Toro Z Master Z597-D - User Manual

Toro Z Master Z597-D
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
2004—The Toro Company
8111 Lyndale Ave., Blomington, MN 55420, USA
Printed in the USA
All Rights Reserved
Original Instructions (EN)
Register your product at www.Toro.com
Z500 Series Z Master
Diesel Mowers
Form No. 3351–414 Rev A
Setup Instructions
Loose Parts
Use the chart below to verify all parts have been shipped.
Step Description Qty. Use
1
No parts needed – Adding fuel to the machine
2
No parts needed – Raising the machine up
3
Roll bar, right section
Roll bar, left section
Roll bar, center section
Bolt, 3/8 x 1 inch
Curved washer
Flange nut, 3/8 inch
Bolt, 1/2 x 3-1/4 inches
Flange nut, 1/2 inch
Lanyard
1
1
1
8
8
8
2
2
2
Installing the roll over protection system
(ROPS)
4
Wheels 2 Installing the drive wheels
5
No parts needed – Checking the tire pressure
6
Control lever–right
Control lever–left
Bolt, 3/8 x 1 inch
Curved washer, 3/8 inch
1
1
4
4
Adjusting the motion control levers
7
Bulk electrolyte with 1.265 specific gravity
(Purchase from a battery supply outlet.)
1 US
Gallon
Activating the battery for international
machines only
8
No parts needed –
Charging the battery for international and
domestic machines
9
Number 2 general purpose lithium base or
molybdenum base grease. (Purchase
separately.)
1 tube Greasing the bearings
10
No parts needed – Preparing the side discharge chute

Table of Contents

Questions and Answers

  • A
    Aaron GarciaAug 11, 2025
    How to fix abnormal vibration in my Toro Z Master Z597-D Lawn Mower?
    • R
      Robert OrtegaAug 12, 2025
      Abnormal vibration in your Toro Lawn Mower can be due to several reasons. The cutting blade(s) might be bent or unbalanced, in which case you should install new cutting blade(s). Alternatively, a blade-mounting bolt could be loose, requiring you to tighten it. It's also possible that a blower pulley or pulley assembly is loose, so tighten the appropriate pulley. A worn blower belt can also cause vibration, requiring a replacement. If the blower fan blade(s) is/are bent or unbalanced, contact an Authorized Service Dealer.
  • L
    Lisa HernandezAug 18, 2025
    Why is there debris blow out from my Toro Z Master Z597-D?
    • M
      Michael DavisAug 18, 2025
      Debris blow out from your Toro Lawn Mower can be caused by a bagger that is too full, so you should dump the bagger more frequently. It may also happen if the ground speed is too fast, so drive slower at full throttle. Also, the mower deck might not be level.
  • C
    Christopher TurnerAug 27, 2025
    What to do if the blower and tubes plug too frequently on my Toro Z Master Z597-D?
    • C
      Christopher JacksonAug 27, 2025
      Frequent plugging of the blower and tubes in your Toro Lawn Mower can occur if the bagger is too full, so dump the bagger more frequently. Always operate the collection system at full throttle. Avoid cutting grass when it is wet, and do not cut more than 51-76 mm (2-3 inches) or 1/3 of the grass height, whichever is less. Clear the screen in the bagger hood of debris, leaves, or grass clippings. Reduce your ground speed while maintaining full throttle, and replace the blower belt if it is worn.
  • B
    browncraigSep 2, 2025
    What to do if the blower impeller does not spin freely on my Toro Z Master Z597-D Lawn Mower?
    • A
      alexa60Sep 3, 2025
      If the blower impeller on your Toro Lawn Mower does not spin freely, it could be plugged. Remove any debris, leaves, or grass clippings from the blower impeller. If the impeller is not aligned, contact an Authorized Service Dealer.

Toro Z Master Z597-D Specifications

General IconGeneral
BrandToro
ModelZ Master Z597-D
CategoryLawn Mower
LanguageEnglish

Related product manuals