Toshiba 40PU200 series - Initial TV Tuning and PC Connection Details; Tuning the TV for the First Time; PC Connector Pin Assignment

Signal names for mini D-sub 15 pin connector
Pin assignment for RGB/PC terminal
Pin No. Signal name Pin No. Signal name
1R 9NC
2 G 10 Ground
3 B 11 NC
4 NC (not
connected)
12 DDC Data
5 NC 13 H-sync
6 Ground 14 V-sync
7 Ground 15 DDC Clock
8 Ground
• Most of the picture/sound controls and functions
are available. However features not available will
be greyed out.
Turning the TV on
Switching on the TV
Connect the power cord to a wall outlet, the
! power indicator lights in red (standby mode).
1 Press on the remote control or ! on the TV
left side panel, the ! power indicator lights in
green.
Note:
If you watch black and white programmes when the
Colour System mode is set to “A” (Automatic), colour
noise may appear on the screen. In this case select the
appropriate Colour System (For the system of each
country or region, refer to pages 11, 29).
Switching o the TV
1 Press on the remote control or ! on the TV
left side panel to switch to the standby mode.
Notes:
• When the TV will not be used for a long period of
time, such as during vacation or travel, remove the
power plug from the wall outlet.
• The TV will automatically turn itself o after
approximately 15 minutes if it is tuned to a vacant
channel or a station that completes its broadcast
for the day. This function does not work in external
input or Blue screen O mode.
The TV will automatically turn itself o after
approximately 2 hours if you do not operate the TV
after turned on by on timer function.
• If power is cut o while you are viewing the TV,
the Last Mode Memory function turns on the TV
automatically when power is applied again. If power
is going to be o for a long time and you are going
to be away from your TV, unplug the power cord to
prevent the TV from turning on in your absence.
Tuning the TV for the  rst time
Before switching on the TV, put your decoder and
media recorder to standby, if they are connected,
and ensure that the aerial is connected. To setup
the TV, use the buttons on the remote control as
detailed on page 7.
1 Press the button. The Quick Setup screen
will appear. This screen will appear the  rst time
that the TV is switched on.
Quick Setup
Language English
2 Press  or  to select the menu language
(English, Chinese (CS), Malay, Thai, Vietnamese,
Russian, Arabic, Persian, French or Indonesia).
3 Press Q, to display the Location menu.
Press  or  to select Store or Home. For
normal home use, select Home.
You can select either Home or Store mode.
Home is recommended for normal home use.
Select Store when using a TV for displaying in
a shop, etc.
Location
Home
To use the TV for displaying in
a store showroom, please select [Store].
[Home] mode is recommended
for normal use.
4 Press Q to display the Auto Signal Booster
menu, and then  or  to select Ye s or No.
Auto Signal Booster
Yes
Signal Booster boosts weak analogue broadcast signals.
If you select [Yes], the TV will automatically set this
feature to [On] or [Off] according to signal strength.
Do you wish to enable automatic control?
Yes mode :
This function performs automatic distinction of
On or O .
5 Press Q to display the Auto Tuning startup
screen. Press Q to start the automatic search.
Auto Tuning
Progress
Found
1% 0
When the automatic search is completed,
the TV will automatically appear the Manual
Tuning menu.
Use the Manual Tuning operation if desired
channels cannot be preset with the Auto
– 10 –
233240PU200SeriesEN0620.indd10233240PU200SeriesEN0620.indd10 2012/06/268:04:412012/06/268:04:41