To Next PageTo Next PageWhy won't the compressor turn on in my Toshiba RAS-10UKP-ES3 Air Conditioner, even though it should?
The compressor in your Toshiba Air Conditioner might not turn on immediately due to a restart delay timer, which lasts for 3 minutes. This timer is also active after the power supply is turned on.
Why doesn't the compressor turn off on my Toshiba RAS-10UKP-ES3 Air Conditioner, even when it's cold enough?
Your Toshiba Air Conditioner's compressor is designed to run for at least 3 minutes after being turned on, even if the room temperature reaches the point where it should turn off.
What should the power supply voltage be for a Toshiba RAS-10UKP-ES3?
The Toshiba Air Conditioner requires a line voltage of AC 220 - 240V.
Why does the operation mode change in Automatic operation on my Toshiba RAS-10UKP-ES3 Air Conditioner?
In Automatic operation, your Toshiba Air Conditioner constantly monitors the room temperature to adjust the fan speed and operation mode. The mode changes every 15 minutes based on the difference between the current room temperature and your set temperature.
How to check cable connection between indoor and outdoor units of Toshiba Air Conditioner?
Ensure that the indoor and outdoor units of your Toshiba Air Conditioner are properly connected. Verify that the terminals with the same numbers are correctly matched between the units.
Why doesn't the Hi-POWER operation work on my Toshiba RAS-10UKP-ES3 Air Conditioner?
The Hi-POWER operation on your Toshiba Air Conditioner will not function if the unit is currently in Dry operation or Fan only operation.
What does it mean when the PRE-DEF. lamp is on when Heating starts on my Toshiba RAS-10UKP-ES3?
The PRE-DEF. lamp on your Toshiba Air Conditioner indicates that the Defrosting operation is in progress or the indoor heat exchanger temperature is low when the Heating operation starts. To prevent cold air from blowing into the room, the indoor fan motor will stop at this time.
Why does the outdoor fan motor stop when heating with my Toshiba RAS-10UKP-ES3?
The outdoor fan motor on your Toshiba Air Conditioner may stop during Heating operation due to a high-temperature limit control operation when the indoor heat exchanger temperature is high.
Why is my Toshiba RAS-10UKP-ES3 stuck on Fan only mode in Automatic operation?
If the room temperature is within ± 1°C of the preset temperature in Automatic operation, your Toshiba Air Conditioner will select Fan only operation.
General| Cooling Capacity | 2.5 kW |
|---|---|
| Heating Capacity | 3.2 kW |
| Refrigerant | R410A |
| Power Supply | 220-240V, 50Hz |
| Indoor Unit Weight | 9 kg |
| Energy Efficiency Ratio (EER) | 3.21 |
| Coefficient of Performance (COP) | 3.61 |
Specifies the type of air conditioner covered in the manual.
Provides detailed diagrams of the unit's construction.
Explains the basic control logic and components of the air conditioner.
Highlights critical safety precautions for installation.
Highlights critical safety precautions for installation.
Provides diagrams for positioning indoor and outdoor units.
Detailed steps for connecting refrigerant pipes.
Procedure for evacuating air from the refrigerant system.
Lists electrical parts for specific indoor units.
General steps for troubleshooting.
How to use the remote for self-diagnosis.
Flowcharts to guide troubleshooting steps.
Procedures for replacing parts of the indoor unit.
Procedures for replacing parts of the outdoor unit.
Exploded view and parts list for the indoor unit (heat pump).
Exploded view and parts list for the indoor unit (cooling).
Exploded view and parts list for specific outdoor units.
Exploded view and parts list for specific outdoor units.
Exploded view and parts list for specific outdoor units.
Exploded view and parts list for specific outdoor units.
Exploded view and parts list for a specific outdoor unit.
