Warning
Do not set "Audio Out Select" to "Bitstream" from the on-screen displays [_[_ unless you are connecting (via the
BITSTREAM/PCM AUDIO OUT jack) an AV decoder that has the Dolby Digital, Digital Theater Systems (DTS) or MPEG2
decoding function. High volume sound may damage your hearing as well as the speakers
When playing DTS-encoded discs (DVD video discs and audio CDs), excessive noise may be output from the analog
stereo jacks. To avoid possible damage to the audio system, you should take proper precautions when the 2CH AUDIO
OUT jacks of the DVD video player are connected to an amplification system To enjoy DTS Digitar Surround TM playback,
an external 5.1 channel DTS Digital Surround TM decoder system must be connected to the BtTSTREAM/PCM AUDIO OU]
jack of the DVD video player.
I Connecting to
Digital Theater Systems (DTS)
DTS is a high quality surround technologyused in theaters and now available for home use,
on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtainthe fullbenefit of 5 1 channel DTS
encoded sound tracks on DVD video discs oraudio COs.
an amplifier equipped with a DTS decoder 1
Amplifierequippedwith _
a DTS decoder [ '-_ _'_
ToOPTICAL ToCOAXIAL _ _ :
type digital typed_gital _ _,
audio input 75 _ZcoaxiaIConneCtcableeither"[_yilJ]
Optical digital cable J
'DTS" and "DTS Digital Surround' are
trademarks of Digital Theater Systems,
Inc
• Use DVD video discs or audio
CDs encoded via the DTS
recording system.
Make the following setting.
Setting Select:
t
'Audio Out Select' I "Bitstream"
Recording system DTS
Page
I Connecting to
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs withdynamic realistic sound
by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio
processor
MPEG2 audio decoder _ _ _ _)_
To OPTICAL_'_ TOCOAXIAL L
_--[- audioinputYpedga _1_ audioinputypedga _ Connect elther._
_- I _ 75 ,2 6oaxial cable _ly
E_] + _ Optical digital cable J Recordingsystem MPEG
I Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier
equipped with a digital audio input and speaker system (right and left front speakers)
an amplifier equipped with an MPEG2 audio decoder
(3
O
• Use DVD video discs encoded via
the MPEG2 recording system.
• Make the following setting.
Setting Select: Page
'Audio Out Select" "Bitstream" I_
"F-
Amplifier equippedwith " _
a digital audioinput •
[ T_'OPTICAL _, ToCOAX'_'ALL_++ ° ° ° °f,_
typedigital type digital
taY_dioinput yf audioinput C°nnect e'ther- _1_
._1 /1._._ 75 ,, coaxial cable _y
_ Optical digitalcable J
• Make the following setting.
Setting Selech _
"Audio OUt Select .... PCM"
Notes
• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD video ptayer to the AC+3 RF input of a Dolby Digital
Receiver. This input on your AN Receiver is reserved for Laserdisc use only and is incompalible with the BITSTREAM/PCM
AUDIO OUT jack of the DVD video player.
• Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD video player to the "OPTICAL" or "COAXIAL" input of a Receiver
or Processor
• Refer to the owner's manual of the connected equipment as well
• When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• The output sound of the DVD video player has a wide dynamic range Be sure to adjust the receiver's volume to a moderate
listening level Otherwise, the speakers may be damaged by a sudden high volume sound
• Turn off the amplifier before you connect or disconnect the DVD video player's power cord. If you leave the amplifier power
on, the speakers may be damaged. 19 [
To Next Page
Loading...
