To Next PageTo Next PageWhy does my Toshiba Projector say 'NO INPUT IS DETECTED ON ***'?
This message on your Toshiba Projector means there is no input signal. Confirm the signal input connection and the status of the signal source.
Why do colors have a faded-out appearance, or color tone is poor on my Toshiba TLP-SX3500 Projector?
If the colors on your Toshiba Projector appear faded or the color tone is poor, adjust the color settings by changing the COLOR BAL R, COLOR BAL G, COLOR BAL B, COLOR, and/or TINT settings in the menu.
What to do if my Toshiba TLP-SX3500 shows 'There is a possibility that the interior portion has become overcooled'?
If your Toshiba Projector displays this message, use the unit within the specified temperature range (0°C to 35°C). After doing so, reset the power to ON.
What does 'SYNC IS OUT OF RANGE ON *** fH *****kHz fV *****Hz' mean on my Toshiba TLP-SX3500 Projector?
This message on your Toshiba Projector indicates that the horizontal or vertical wavelength of the input signal is outside the unit's response parameters. Check the specs for the unit or the signal source.
Why does my Toshiba TLP-SX3500 Projector power not come on?
The power may not be coming on for several reasons: * The electrical power cord might not be properly plugged in; ensure it's correctly connected. * The power switch might not be in the on position; set it to the [ | ] (On) position. * The main power source could have been interrupted; turn the power off, let the unit cool for at least 20 minutes, and then turn it back on. * The lamp or lamp cover might not be properly fixed; turn the power off, let the unit cool for at least 45 minutes, and then check the attachment of the lamp and cover.
What to do if my Toshiba TLP-SX3500 Projector cooling fan is not operating?
If the cooling fan on your Toshiba Projector is not working, turn the power off and let the unit cool down for at least 20 minutes. After it has cooled, check that no foreign objects are caught in the fan, and then turn the power back on.
What to do if my Toshiba Projector shows 'Either there is no lamp and/or lamp cover, or either of these has not been properly fixed'?
If your Toshiba Projector displays this message, turn the power off and let the unit cool down for at least 45 minutes. After cooling, check the attachment of the lamp and lamp cover, and then turn the power back on.
What to do if my Toshiba Projector shows 'REMINDER *** HRS PASSED AFTER THE LAST FILTER CHECK'?
This message on your Toshiba Projector indicates that the filter timer has reached the interval set in the OPTION menu. Clean or change the air filter, and then reset the filter timer.
What does it mean when my Toshiba TLP-SX3500 Projector says 'CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. THE POWER WILL TURN OFF AFTER 0 hr.'?
This message on your Toshiba Projector means that the lamp timer has reached 2000 hours, and the power will soon turn off automatically. Immediately turn the power off, change the lamp, and reset the lamp timer.
What does it mean when my Toshiba TLP-SX3500 Projector says 'CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. THE POWER WILL TURN OFF AFTER ** hr.'?
This message on your Toshiba Projector indicates that the lamp timer is approaching 2000 hours, and a lamp change within the specified time is recommended. The power will automatically turn off when the lamp reaches 2000 hours. Change the lamp and reset the lamp timer.
General| Contrast Ratio | 2000:1 |
|---|---|
| Display Type | 3LCD |
| Projection Size | 30 to 300 inches |
| Resolution | XGA (1024 x 768) |
| Lamp Life | 2000 hours (normal mode), 3000 hours (eco mode) |
| Input Ports | S-Video |
| Outputs | Audio |
Important safety instructions and warnings before operating the projector.
Essential safety guidelines and hazard symbols for projector operation.
Detailed safety instructions covering installation, use, and servicing of the projector.
Safety guidance for damage requiring service, glass components, and servicing procedures.
Detailed identification of buttons on the projector's control panel and the remote control.
Guidelines for projector placement and determining screen size based on distance.
Guidance on connecting external devices and the projector's Plug-and-Play capability.
Methods for choosing the video input source using the INPUT dial or buttons.
Step-by-step instructions for safely replacing the projector lamp.
Procedures for cleaning or replacing the air filter and resetting the filter timer.
Explanations of messages displayed on the projector and their solutions.
Meanings of the STANDBY/ON, LAMP, and TEMP indicator lights.
Common issues not indicating a machine defect and their possible causes.
