TP-Link Jetstream Series User Manual

7106508579 REV3.0.0
JetStream Gigabit Smart PoE+ Switch
Ethernet Ports (1–8)
1. To access the GUI of the switch, open a browser and type the default
management address http://192.168.0.1 in the address eld of the
browser, then press the Enter key.
2. Enter admin for both the username
and password in the lower case
letters. Then click the Log In button
or press the Enter key. (The rst time
you log in, change the password to
better protect your network and
devices.)
3. After a successful login, the main
page will appear. You can click the
menus on the top side and left side
to congure the corresponding
functions.
Note:
For more details about how to congure the switch, see the Conguration
Guide on the resource CD.
PC
Note:
To log in to the switch, the IP address
of your PC should be set in the same
subnet as that of the switch. The IP
address is 192.168.0.x (”x” is any
number from 2 to 254). Subnet Mask
is 255.255.255.0. For details, please
refer to Appendix B in the User Guide
on the resource CD.
SFP Slots
IP Camera AP IP Phone
PoE Devices
Note:
1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. Maximum PoE power is 30 W for each PoE port and 58 W for all PoE ports.
DC Power Adapter
AC Power Cord
LED Explanation
Installation Guide
Conguration
Connection
On: Power on
O: Power o
Power
Power
SPF1/SFP2
On (Green): Connected to a 1000 Mbps
device
On (Yellow): Connected to a 100 Mbps
device
Flashing: Transmitting/receiving data
SPF1 SPF2
Flashing: System running normally
On/O: System running abnormally
System
System
On: 51 W≤Total power supply<58 W
Flashing: Total power supply keeps≥
51 W more than 2 minutes
O:
Total power supply<51 W
PoE MAX
PoE MAX
PoE Status (port 1–8)
On: Providing PoE power
Flashing: Current-overload/Short-circuit/
Connected to a Non-standard PD/Power
exceeded the user-dened value
O: Not providing PoE Power
PoE Status
Link/Act (port 1–8)
On (Green): Running at 1000 Mbps
On (Yellow): Running at 10/100 Mbps
Flashing: Transmitting/receiving data
Link/Act
Internet
1
2
3

TP-Link Jetstream Series Specifications

General

Model	Jetstream Series
Type	Multiple types exist within the Jetstream Series
Ports	Multiple port configurations exist within the Jetstream Series
Layer	Layer 2/Layer 3
PoE Support	Available on some models
Uplink Ports	Varies depending on the specific model
Switching Capacity	Varies depending on the specific model
Forwarding Rate	Varies depending on the specific model
MAC Address Table	Varies depending on the specific model
Packet Buffer	Varies depending on the specific model
Power Consumption	Varies depending on the specific model
Dimensions	Varies depending on the specific model
Weight	Varies depending on the specific model
VLAN Support	Yes
QoS	Yes
Management	CLI, SNMP

Summary

LED Explanation

Power and System Status LEDs

Details on Power, System, and POE MAX LED indicators, explaining their states and meanings.

Port Status LEDs

Explanation of Link/Act, PoE Status, and SPF1/SFP2 LEDs for port connectivity and status.

Device Connection

Physical Connections

Illustrates connecting AC power, DC power adapter, and network cable (Internet) to the switch.

PoE Port Usage

Notes on PoE port capabilities, supporting non-PoE devices and maximum power limits.

Switch Configuration

Accessing the Management GUI

Steps to access the switch's Graphical User Interface via its default IP address.

Login and Initial Setup

Instructions for logging in with default credentials and a recommendation to change the password.

Navigating Configuration Menus

Guidance on using menus on the top and left sides to configure switch functions after login.

Specifications and FAQ

General and Environmental Specifications

Details on standards, data transfer rates, network media, port counts, and environmental operating conditions.

Frequently Asked Questions

Answers to common issues regarding Power LED, Link/Act LED, and PoE port power supply.