TP-Link TL-SG1008P Installation Guide

Connection
© 2020 TP-Link 7106508569 REV3.1.0
Installation Guide
Gigabit Desktop Switch with PoE/PoE+
LED Explanation
Power
On: Power on
O: Power o
Link/Act (For TL-SG1008P)
On: A device is linked to the correspoding
port and running properly.
Flashing: Transmitting or receiving data.
O: No device is linked to the
corresponding port.
Link/Act, Uplink 1, Uplink 2 (For TL-SG1210P)
Green On: Running at 1000 Mbps, but no activity.
Green Flashing: Running at 1000 Mbps and is
transmitting or receiving data.
Yellow On: Running at 10/100 Mbps, but no activity.
Yellow Flashing: Running at 10/100 Mbps and is
transmitting or receiving data.
O: No device is linked to the corresponding port.
Package Contents: Switch, Power Adapter, Power Cord and Installation Guide.
On: Providing PoE power
Flashing: PoE fault
O: Not providing PoE power
PoE Status
On: Running at 1000 Mbps.
O: Running at 10/100 Mbps or no device
is linked to the corresponding port.
1000Mbps (For TL-SG1008P)
PoE MAX
For TL-SG1008P:
On: 48 W≤Total power supply < 55 W
Flashing: Total power supply ≥ 55 W
O: Total power supply < 48 W
For TL-SG1210P:
On: 56 W≤Total power supply < 63 W
Flashing: Total power supply ≥ 63 W
O: Total power supply < 56 W
Note: For simplicity, we will take TL-SG1008P for example throughout the Guide.
PC
IP Camera AP
Ethernet Ports (1-8)
PoE Ports (1-4)
IP Phone
PoE Devices
Router
LAN PortWAN Port
Internet
DC Power Adapter
AC Power Cord
Note:
PoE/PoE+ ports typically connect to PoE Devices. Besides, PoE/PoE+ ports can also connect to non-PoE devices, but only transmit data.
TL-SG1210P has two uplink ports, which typically connect to uplink devices like routers.
Uplink 1 is an SFP port and works with a 1000 Mbps SFP module. Uplink 2 is an RJ45 port.
For TL-SG1008P, maximum PoE power is 15.4 W for each PoE port and 55 W for all PoE ports in total.
For TL-SG1210P, maximum PoE power is 30 W for each PoE port and 63 W for all PoE ports in total.
1.
2.
3.
4.
PoE budget calculations are based on laboratory testing. Actual PoE power budget is not guranteed and will vary as a result of client
limitations and environmental factors.

TP-Link TL-SG1008P Specifications

General

Switch type	Managed
Quality of Service (QoS) support	No
Power connector	DC-in jack
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
Flow control support	Yes
Networking standards	IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x
Cable types supported	Cat3, Cat4, Cat5, Cat5e
Copper ethernet cabling technology	1000BASE-T, 100BASE-TX, 10BASE-T
Jumbo frames	16000
Forwarding rate	11.904 Mpps
MAC address table	4000 entries
Power source	DC/PoE
Input current	1.31 A
AC input voltage	100 - 240 V
DC input voltage	53.5 V
AC input frequency	50/60 Hz
Power consumption (max)	75 W
Number of power supply units	1
Product color	Gray
Housing material	Metal
Heat dissipation	225.75 BTU/h
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 90 %
Total Power over Ethernet (PoE) budget	64 W
Power over Ethernet (PoE) ports quantity	4
Package type	Box
Package depth	280 mm
Package width	223 mm
Package height	68 mm
Package weight	900 g
Cables included	AC
Maximum cable length	100 m
Sustainability certificates	CE, Federal Communications Commission (FCC), RoHS

Weight and Dimensions

Depth	98 mm
Width	171 mm
Height	27 mm