TP-Link TL-SG108E Installation Guide

Overview of the Product
1
8-Port Gigabit Easy Smart Switch
MODEL NO. TL-SG108E
Package Contents
Installation Guide
IG
TL-SG108E
MODEL NO.
TL-SG108E
Installation Guide
8-Port Gigabit Easy Smart Switch
The TL-SG108E 8-Port Gigabit Easy Smart Switch is an ideal upgrade from an unmanaged switch, designed for Small and Medium Business networks
that require simple network management. Network administrators can eectively monitor trac via Port Mirroring, Loop Prevention and Cable Test
features. To optimize trac on your business network, it oers both port and tag based QoS to keep latency-sensitive trac moving smoothly and
jitter-free. Additionally, port-based, tag-based and MTU VLAN can improve security and meet more network segmentation requirements. Moreover,
with the innovative energy-ecient technology, they are eco-friendly solution for your business network.
Front Panel
Rear Panel
1. Make sure that the box contains the above items. If any of
the listed items are damaged or missing, please contact
your distributor.
2.
The switch or TL-SG108E mentioned in this User Guide
stands for TL-SG108E 8-Port
Gigabit Easy Smart Switch
without any explanation.
Initialization
1. The Power LED indicator will light on all the time.
2.
After keeping o for several seconds, the rest of the LED
indicators will ash momentarily, and then work normally
after the initialization.
Powering on the switch, it will automatically initialize and its LED
indicators will respond as follows:
If the LED indicators don’t respond as described above,
please check the power supply and its connection.
Resource CD
Power LED
On: Power on
O: Power o
Ethernet Ports(1-8)
Reset Button
10/100M LED(Yellow)
On: Connected to a 10/100Mbps device
Flashing: Transimitting/receiving data
Kensington
Security Slot
Power Socket
Power Cord and Rubber Cushions
Installation
2
Connection
3
The switch can be either located on a desktop or mounted on a wall.
7106504641 REV1.0.0
1
Mounting the Switch on a Desk
2
Place the switch upside down on a at desk．
Step 1.
Remove the adhesive backing paper from the rubber
cushions.
Step 2.
Attach the supplied four rubber cushions to the
recessed areas on the bottom at each corner of the
switch.
Step 3.
Step 4.
Turn over the switch.
Mounting the Switch on a Wall
Bottom of the Switch
L=110mm
Drill two holes into the wall. Insert a screw into each hole
and leave a part of its head exposed.
Step 1.
Place the two wall-mounting slots over the screws and
slide the switch down to fasten it.
Step 2.
3
Connect equipment
Step 1.
Connect power
Step 2.
1000M LED(Green)
On: Connected to a 1000Mbps device
Flashing: Transimitting/receiving data
RJ45
Cable
TL-SG108E
Router
(TL-ER604W for example)
Cable
Cable
Modem
(
TD-8816 for example)
WAN
LAN
Internet
Line

TP-Link TL-SG108E Specifications

General

Switch type	Managed
Switch layer	L2
Quality of Service (QoS) support	Yes
Installed SFP modules quantity	-
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
10G support	No
Number of VLANs	32
Networking standards	IEEE 802.1ab, IEEE 802.1p, IEEE 802.1Q, IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Virtual LAN features	Port-based VLAN
Cable types supported	Cat3, Cat4, Cat5, Cat5e
Security algorithms	SNMP, SNMPv2, SNMPv3
Jumbo frames	15000
Forwarding rate	11.9 Mpps
MAC address table	4000 entries
Packet buffer memory	1.5 MB
Certification	FCC, CE, RoHS
Product color	Black
Housing material	Metal
Heat dissipation	12.12 BTU/h
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 90 %
Power source	DC
Input current	0.6 A
Input voltage	9 V
Power consumption (max)	3.55 W
Package type	Box
Package depth	191 mm
Package width	130 mm
Package height	92 mm
Package weight	630 g
Cables included	AC

Weight and Dimensions

Depth	101 mm
Width	158 mm
Height	25 mm