TP-Link TL-SG1210MP User Manual

Installation Guide
Unmanaged Desktop PoE+ Switch
© 2021 TP-Link 7106509290 REV6.0.1
Switches Explanation (Only for TL-SG1210MP)
O: Ports run at 10/100/1000 Mbps and support PoE power supply up to 100 m away.
On: Ports run at 10 Mbps and support PoE power supply up to 250 m away.
Extend
Connection
Note: For simplicity, we will take TL-SG1008P for example throughout the Guide.
PC
IP Camera AP
Ethernet Ports (1-8)
PoE Ports (1-4)
IP Phone
PoE Devices
Router
LAN PortWAN Port
Internet
DC Power Adapter
AC Power Cord
Note:
PoE ports can also connect to non-PoE devices, but only transmit data.
O: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered device (PD).
When the switch nds that the PD works abnormally, the switch will reboot it.
Recovery
Note: The numbers in brackets indicate the ports where the feature takes eect. For example, when Extend(1-4) is toggled to On, the Extend mode will be enabled for ports 1-4.
O: Ports can transmit data with each other.
On: Specic ports cannot transmit data with other downlink ports. They can transmit data
only with the uplink ports.
Isolation
O: All the ports transmit data with the same priority.
On: The specic ports transmit data with a higher priority than other ports.
Priority
For TL-SG1210MP:
On: 116 W≤Total power supply < 123 W
Flashing: Total power supply ≥ 123 W
O: Total power supply < 116 W
LED Explanation
Power
PoE Status
On: Providing PoE power
Flashing: PoE fault
O: Not providing PoE power
On: Power on
O: Power o
Link/Act; Uplink 1, Uplink 2
Green On:
Running at 1000 Mbps, but no activity.
Green Flashing:
Running at 1000 Mbps and is transmitting or
receiving data.
Yellow On:
Running at 10/100 Mbps, but no activity.
O:
No device is linked to the corresponding port.
Yellow Flashing:
Running at 10/100 Mbps and is transmitting
or receiving data.
PoE Max
For TL-SG1008P:
On: 57 W≤Total power supply < 64 W
Flashing: Total power supply ≥ 64 W
O: Total power supply < 57 W
For TL-SG1210P:
On: 56 W≤Total power supply < 63 W
Flashing: Total power supply ≥ 63 W
O: Total power supply < 56 W

TP-Link TL-SG1210MP Specifications

General

Combo SFP ports quantity	1
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	9
10G support	No
Auto-negotiation	Yes
Networking standards	IEEE 802.3af, IEEE 802.3at, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Cable types supported	Cat3, Cat4, Cat5, Cat5e
Copper ethernet cabling technology	10BASE-T, 100BASE-TX
Power source	DC
Input current	2.43 A
Input voltage	53.5 V
Power supply included	-
Power consumption (max)	141.4 W
Total Power over Ethernet (PoE) budget	123 W
Power over Ethernet (PoE) power per port	30 W
Power over Ethernet plus (PoE+) ports quantity	8
Heat dissipation	482.17 BTU/h
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 90 %
MAC address table	4000 entries
Packet buffer memory	14.88 MB
Certification	CE, FCC
Product color	Black
Switch type	Unmanaged
Harmonized System (HS) code	85176990
Package depth	315 mm
Package width	240 mm
Package height	70 mm
Package weight	1410 g

Weight and Dimensions

Depth	126 mm
Width	209 mm
Height	26 mm