To Next PageTo Next PageHow to fix incorrect indoor temperature display on my Trane Control Unit?
If the indoor temperature display on your Trane Control Unit is incorrect, it may be due to: * The indoor temperature display needing calibration. Calibrate the temperature sensor from the 1050 Control’s menu. * Surrounding air flow affecting the sensed temperature of the 1050 Control.
What to do if heating will not come on with Trane Control Panel?
If your heating isn't turning on with the Trane 1050 Control Panel, here are a few things to check: * Make sure the system mode is set to Heat/Auto and the setpoint is higher than the room temperature. * Wait for 5 minutes to ensure the minimum off time delay isn't being enforced. * If the issue persists, the heating system may require service; check and repair the system.
What to do if cooling will not come on with Trane Control Panel?
If your cooling isn't turning on with the Trane 1050 Control Panel, here are a few things to check: * Ensure the system mode is set to Cool/Auto and the setpoint is lower than the room temperature. * Wait for 5 minutes to ensure the minimum off time delay isn't being enforced. * If the issue continues, the cooling system may need service; check and repair the system.
Why won't the display on my Trane Control Unit come on?
If the display of your Trane Control Unit 1050 does not turn on, it might be due to a loss of 24VAC between R & B. To resolve this: * Check the wiring between R & B. * Check the transformer for 24VAC output. * Check for broken or shorted thermostat wire.
What to do if my Trane Control Unit screen is not responding?
If the screen of your Trane Control Unit does not respond properly when a button is pressed, it could be due to: * The screen being out of calibration. Remove the 1050 Control from the sub base and reset it. Follow the calibration instructions when the 1050 Control reboots. * An internal 1050 Control fault. Remove the 1050 Control from the sub base and reset it. * Screen Lock being enabled. Press and hold the Menu button for 5 seconds to override the screen lock.
Why is the cooling not working on my Trane Control Unit?
If the cooling system of your Trane Control Unit does not turn on, here's what you can check: * Ensure the system mode is set to Cool/Auto, or the setpoint is not too high. Set the mode to cool and lower the setpoint below the room temperature. * The minimum off time delay might be active. Wait for 5 minutes and recheck the cooling equipment. * The cooling system may require service. Check and repair the system.
Why does the time set on my Trane Control Panel change every 24 hours?
If the time set on your Trane 1050 Control changes every 24 hours, the 1050 Control is connected to Trane Home, and the time zone set on your Trane Home account is incorrect. Correct the time zone set on your Trane Home account.
Why is the heating not working on my Trane Control Unit?
If the heating system of your Trane Control Unit does not turn on, it could be due to several reasons: * The system mode might not be set to Heat/Auto, or the setpoint is set too low. In this case, set the mode to heat and raise the setpoint above the room temperature. * The minimum off time delay might be in effect. Wait for 5 minutes and recheck the heating equipment. * The heating system may require service. Check and repair the system.
What to do if the fan is set to ON but not running on my Trane Control Panel?
If the fan is set to ON but not running on your Trane 1050 Control Panel, the Smart Continuous Fan feature might be engaged. If indoor humidity is higher than the desired setpoint, the blower will cycle off with the equipment. A humidity icon will be displayed on the Fan Mode button when the blower operation is being inhibited due too high humidity. Also, the blower motor might not be functioning, so check and repair the system.
What to do if the room temperature overshoots when the Heat/Cool setting is changed more than 2° on Trane Control Panel?
Room temperature overshooting on your Trane 1050 Control Panel when changing the Heat/Cool setting by more than 2° can occur if the heating/cooling equipment is oversized for the current conditions, preventing the 1050 Control from responding quickly enough. Also, it can be caused by an improper location of the 1050 Control. Compare heat load calculation to equipment chosen and relocate the 1050 Control or use a remote sensor.
General| Display | 7-inch color touchscreen |
|---|---|
| Connectivity | Wi-Fi |
| Scheduling | 7-day programmable |
| Humidification Control | Yes |
| Dehumidification Control | Yes |
| Geofencing | Yes |
| Alerts and Notifications | Yes |
| Compatibility | Compatible with Trane and American Standard HVAC systems |
| Voice Control | Amazon Alexa |
| Energy Management | Energy usage reports |
| Power Method | Hardwired |
| Zoning Capability | Yes, with compatible zoning system |
| Remote Access | Yes, via Nexia app |
