Trane TZEMT500AB32MAA User Manual

18-HD39D1-4
Thermostat
Installation Instructions
Models TZEMT400AB32MAA
TZEMT500AB32MAA
P516-275
The TZEMT400 and TZEMT500 Thermostats are compatible with single and multistage forced air
systems, including:
• Gas furnace systems
• Oil furnace systems
• Electric furnace systems
• Heat pump systems
• Air conditioning systems
The TZEMT400 and TZEMT500 Thermostats may be compatible with some other system types,
including:
• Boiler systems
• Geothermal systems
• Multi-zoned systems
The TZEMT400 and TZEMT500 Thermostats are not compatible with the following system types:
• Radiant floor systems
• Wall heating systems
• Proprietary HVAC Communication Protocols
ÎÎ The TZEMT400 and TZEMT500 Thermostats are not compatible with
dual fuel systems (gas or oil furnace & heat pump combined) without
adding a dual fuel accessory relay kit. These thermostats do not have
an emergency heat relay when applied with a dual fuel relay kit.
ÎÎ NOTE: A 24 Volt common and hot wire MUST be connected to the
TZEMT400 or TZEMT500 for operation.
Use this guide and the “Thermostat Starter Kit Quick Start Guide” for installation. The information contained in document P516-000,
“Thermostat Model TZEMT043AZ32MAA”, does not apply to this kit.
Schlage LiNK™
Customer Service:
(877) 288-7707
Contents
Physical Installation and Wiring .......................................................................................................................................2
Field Wiring Diagrams - TZEMT500 .................................................................................................................................6
Field Wiring Diagrams - TZEMT400 .................................................................................................................................9
Optional Remote Temperature Sensors Installation - TZEMT500 Only .........................................................................10
System Settings at Thermostat ......................................................................................................................................12
Perform System Checkout .............................................................................................................................................14
Enroll Thermostat into Schlage LiNK™ System .............................................................................................................15
Product Specifications ...................................................................................................................................................16
Operation .......................................................................................................................................................................17
Menu Maps ....................................................................................................................................................................19
User Settings .................................................................................................................................................................20
Installer Settings ............................................................................................................................................................25
Schedules ......................................................................................................................................................................28
LED Reference ...............................................................................................................................................................30
Warranty .........................................................................................................................................................................31

Trane TZEMT500AB32MAA Specifications

General

Brand	Trane
Model	TZEMT500AB32MAA
Category	Thermostat
Language	English

Summary

Physical Installation and Wiring

Review Wiring Charts

Provides guidance on selecting the correct wiring diagram based on system type.

Field Wiring Diagrams - TZEMT500

Field Wiring Diagrams - TZEMT400

Optional Remote Temperature Sensors Installation - TZEMT500 Only

System Settings at Thermostat

Set Time and Date

Configure the thermostat's internal clock and date for accurate operation.

Gas Furnace Multistage Mechanical Settings

Configure advanced settings for multistage gas furnace systems.

Electric Furnace Mechanical Settings

Configure advanced settings for electric furnace systems.

Heat Pump Mechanical Settings

Configure advanced settings for heat pump systems.

Perform System Checkout

Enroll Thermostat into Schlage LINK™ System

Prepare Enrollment Bridge

Prepare the Z-Wave bridge for the thermostat enrollment process.

Enroll Thermostat into Bridge

Connect the thermostat to the Z-Wave bridge for remote control.

Verify Thermostat Enrollment

Confirm successful enrollment of the thermostat with the Z-Wave bridge.

Product Specifications

Operation

Thermostat Display Overview

Explains the various elements and labels visible on the thermostat screen.

Minimized Display Mode

Option to show only the temperature on the thermostat screen.

Control Screen Function Buttons

Details the function of each button (Menu, System Mode, Fan Mode, Schedule Mode).

Menu Maps

User Settings

Set Clock

Configure the thermostat's internal clock and date.

Filter Service

Manage filter replacement reminders and service intervals.

Maintenance Service

Manage maintenance reminders and service intervals for the HVAC system.

Screen Timeout Settings

Adjust the time before the screen reverts to minimized display mode.

Installer Settings

Display Lock

Lock or unlock thermostat buttons to prevent unauthorized changes.

Max Heat Setpoint

Set the maximum allowable heating setpoint.

Min Cool Setpoint

Set the minimum allowable cooling setpoint.

Minimum Run Time (MRT)

Enforce minimum run time for HVAC cycles to prevent rapid cycling.

System Settings

Schedule Enable

Enable or disable the thermostat's local scheduling function.

Recovery Enable

Enable Smart Recovery for gradual temperature adjustments.

H/C Delta Settings

Set minimum separation between heating and cooling setpoints.

Mechanical Settings

HVAC Type

Select the HVAC system type (Gas/Electric or Heat Pump).

Fan Type

Select the fan type for Gas or Electric systems.

Changeover Type (C/O)

Set the heat pump changeover type (w/Cool or w/Heat).

2nd Stage Heat Enable

Enable or disable the 2nd stage heat operation.

Schedules

Enable/Disable Schedules Menu

Control access to the thermostat's scheduling menu.

Load Preset Schedules

Load pre-defined comfort or energy-saving schedules.

View Current Schedule

Display the currently active heating and cooling schedule.

Set Heat and Cool Schedule

Manually configure custom heating and cooling schedules.

LED Reference

Warranty Information