EasyManua.ls Logo

Trane Voyager THD210G User Manual

Trane Voyager THD210G
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
SAFETY WARNING
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-
conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment
by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in the literature and
on the tags, stickers, and labels that are attached to the equipment.
Packaged Rooftop Air Conditioners
Voyager
Electric/Electric
12.5 to 25 Tons, 60/50Hz
February 2017
RT-SVX25M-EN
Installation, Operation,
and Maintenance
Model Number:
TS*150–301
TH*150-300
Question and Answer IconNeed help?

Do you have a question about the Trane Voyager THD210G and is the answer not in the manual?

Trane Voyager THD210G Specifications

General IconGeneral
ModelTHD210G
CategoryAir Conditioner
Cooling Capacity210, 000 BTU/h
Tonnage17.5 tons
RefrigerantR-410A
Voltage460V
Phase3
Compressor TypeScroll

Summary

Introduction and Safety Advisories

Safety Advisories Overview

Defines WARNING, CAUTION, and NOTICE advisories for safe operation.

Field Wiring and PPE Safety

Emphasizes safety for field wiring, grounding, and personal protective equipment.

System Inputs and Sensors

Compressor Protection and Monitoring

Information on compressor disable, phase monitor, and low pressure control.

Installation Preparation and Guidelines

Fiberglass Wool Precautionary Measures

Safety warnings and PPE requirements when handling fiberglass wool.

Rigging and Lifting Procedures

Rigging and Lifting Procedures

Instructions for safely rigging and lifting the unit.

Lifting Equipment Safety

Warning about using properly rated lifting equipment.

Proper Unit Lifting Techniques

Guidance on verifying lift points and ensuring unit balance.

Installation Steps and Requirements

Field Wiring and Grounding Requirements

Crucial safety information for field wiring and grounding.

Electrical and System Connections

Power and Control Wiring

Space Temperature Averaging

Installation Electrical Checks

Hazardous Voltage Warning

Critical warning regarding hazardous voltages during installation.

Electrical Phasing for Three Phase Motors

Guidance on verifying and correcting electrical phasing.

Installation Safety and Control Systems

Live Electrical Component Safety

Safety procedures when working with live electrical components.

Factory-Mounted Unit Options

Capacitor and Wiring Safety Warnings

Safety warnings related to capacitors and field wiring.

Smoke Detector Installation

Return Air Smoke Detector Installation

Step-by-step instructions for installing the return air smoke detector.

Airflow for Smoke Detectors

Pre-Start Procedures

Verifying Proper Air Flow

Procedure for verifying correct air flow with belt drive fans.

Start-Up Procedures

Economizer Start-Up Procedure

Step-by-step guide for starting up the economizer.

Compressor Start-Up Procedure

Procedure for starting up each compressor circuit.

Advanced Start-Up Operations

Heating Start-Up Procedure

Procedure for starting up the heating system.

Final System Set Up

Final System Set Up Checks

Final checks before leaving the unit after installation.

Maintenance Procedures

Rotating Component Safety Warning

Safety warning when working with rotating components.

Troubleshooting Introduction

Hazardous Service Procedures Warning

Safety warnings for maintenance and troubleshooting procedures.

ReliaTel Control Troubleshooting

Diagnosing issues with the ReliaTel control system.

System Status Checkout Procedure

Methods for checking system status and identifying failures.

Troubleshooting Failures and Lockouts

Troubleshooting System, Cooling, and Service Failures

Diagnosing and resolving system, cooling, and service failures.

Resetting Cooling and Heating Lockouts

Procedures for resetting cooling and heating lockouts.

Sensor and Indicator Troubleshooting

Zone Temperature Sensor (ZTS) Testing

Procedures for testing ZTS resistance and setpoints.

Advanced Sensor and Control Testing

Programmable and Digital Zone Sensor Tests

Testing serial communication, RTRM default, and sensor operation.

Economizer Control Troubleshooting

Economizer Control (ECA) Troubleshooting

Diagnosing ECA status and error codes using ReliaTel.

Related product manuals