Tridonic PRO Series User Manual

www.tridonic.com
1
Subject to change without notice. Information provided without guarantee.
Data sheet 10/20-EM091-6
Emergency lighting units
EM converterLED
Product description
• Emergency lighting LED Driver with DALI interface
and automatic test function
• For self-contained emergency lighting
• For LED modules with a forward voltage of 10 – 54 V
• SELV for output voltage < 60 V DC
• Low profile casing (21 x 30 mm cross-section)
• For luminaire installation
• Nominal life-time up to 100,000 h
• 5-year guarantee
Properties
• Non maintained operation
• DALI interface for controlled testing and monitoring
• 1, 2 or 3 h rated duration
• Operating time selectable with plug (duration link)
• Compatible with most constant current LED Drivers (see 5.4)
• 3-pole technology: 2-pole LED module changeover
and delayed power switching for the LED Driver
• Automatic shutdown of output if LED load is out of range
• Constant power output
• Addressing function, patented („EZ easy addressing“)
• Two-colour status display LED
• Electronic charge system
• Deep discharge protection
• Short-circuit-proof battery connection
• Polarity reversal protection for battery provided by 3-pole
connector
• Automatic detection of the connected battery technology
(NiMH or LiFePO
4
batteries)
Tests:
• Status of the battery
• Status of the LED
• Function test
• Duration test
Batteries
• High-temperature cells
• NiMH or LiFePO4 batteries
• LA or 18650 cells
• 4-year design life for NiMH batteries
• 1-year guarantee for NiMH batteries
• 4 – 8 years design life for LiFePO
4
batteries
• 3-year guarantee for LiFePO
4
batteries
• For battery compatibility refer to chapter „Battery selection“
È
Standards, page 5
Wiring diagrams and installation examples, page 6
EM converterLED PRO MH/LiFePO4 50 V
PRO series

Tridonic PRO Series Specifications

General

Product Category	LED Driver
THD	<10%
Protection	Overload, short circuit, over temperature
Certifications	ENEC, CE, RoHS
Input Voltage	220-240 V
Operating Frequency	50/60Hz
Dimming Interface	DALI

Summary

Standards and Compliance

Glow-wire Test

Compliance with EN 61347-1 for glow-wire test at 850 °C.

Insulation and Electric Strength Testing

Guidelines for insulation and electric strength testing of luminaires.

Thermal Details and Life-Time

Product Life-Time

Average life-time of 50,000 hours under rated conditions.

Installation and Wiring

Wiring Diagram

Diagram for connecting LED modules to the EM converterLED.

Wiring Type and Cross Section

Specifications for wire preparation and cross-section.

Battery Connection

Details on connecting NiMH and LiFePO batteries.

Loose Wiring

Instructions for loosening wires using a release tool.

Wiring Guidelines

Best practices for wiring LED terminals, battery, and DALI.

Maximum Lead Length

Permitted lead lengths for LED, status LED, and batteries.

Mechanical Values

Housing Properties

Details on casing material and protection type.

Mechanical Data Accessories

Specifications for test switch and LED status indicator.

Electrical Values

Maximum Loading of Automatic Circuit Breakers

Loading capacities for various circuit breaker types.

Insulation Matrix

Overview of insulation requirements for different connections.

LED Current/Voltage Characteristics

Graphs showing LED current vs. voltage in emergency mode.

LED Driver Compatibility

Maximum ratings for associated LED Drivers.

Functions

Duration Link Selection

Setting the emergency duration via link position.

Status Indication

System status indicated by bi-colour LED and DALI flag.

Testing Procedures

Details on DALI control and self-testing functions.

Battery Data

Battery Selection Guide

Table for selecting compatible batteries based on type and duration.

Battery Charge and Discharge Data

Charge/discharge currents and voltages for NiMH batteries.

NiMH Battery Specifications

Technical details for 4.0 Ah NiMH batteries.

LiFePO4 Battery Specifications

Technical details for 1.5 Ah LiFePO4 batteries.

Battery Safety Features

Protection against deep discharge, overcharge, short-circuit, and overtemp.

Storage, Installation, and Commissioning

Information on battery handling and initial setup.

Miscellaneous Information

Maximum Switching Cycles

Tested switching cycles for the associated LED driver.

Battery Replacement Procedure

Mandatory duration test after battery replacement.

BlackBox Data Recording

Parameters stored for application and usage monitoring.

Additional Information Sources

Links to technical data, guarantee conditions, and services.