EasyManua.ls Logo

Trojan Technologies Trojan UV Max - User Manual

Default Icon
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
A B C E or F or
or D Pro7 Pro15
Lamp part
#
602725 602726 602727 602728 602729
Head Office (Canada)
3020 Gore Road
London, Ontario
Canada N5V 4T7
Tel: (519) 457-3400
Fax: (519) 457-3030
United Kingdom
5 De Salis Crt.
Hampton Lovett, Droitwich
WR9 0QE England
Tel: 44-1-905-771117
Fax: 44-1-905-772270
www.trojanuvmax.com
Printed in Canada. Copyright ©2001Trojan Technologies Inc. London, Ontario, Canada.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means without the written permission of Trojan Technologies Inc.
602669 Rev C
DO NOT REMOVE FROM UNIT
Installation performed by: ___________________________________________________________________________________________________________________
Date of installation: _______________________________________________________________________________________________________________________________
For service and lamp orders, call your installer at: __________________________________________________________________________________
or call Trojan Technologies Inc. at (519) 457-3400
Lamps must be replaced after 12 months of operation to ensure proper
disinfection of your water.
Clean quartz sleeve and UV sensor (if equipped) frequently for optimum performance.
1st: _____________________________ 6th: _____________________________
2nd: _____________________________ 7th: _____________________________
3rd: _____________________________ 8th: _____________________________
4th: _____________________________ 9th: _____________________________
5th: _____________________________ 10th: _____________________________
Model installed: (circle model)
CRITICAL OPERATING INFORMATION INSIDE
See back cover for vital records.
Lamp replacement record:

Table of Contents

Questions and Answers

  • H
    Heather HansonAug 13, 2025
    What to do if the red indicator light glows and the alarm sounds on my Trojan Technologies Water Filtration System?
    • B
      Bryan Sims PhDAug 14, 2025
      If the red indicator light is on and the alarm is sounding, it indicates a problem with the lamp. Here's what you can do: * Check the lamp for continuity across the pins. If there is no continuity, replace the lamp. * If the Elapsed Time Meter reads 12 or more, replace the lamp. * If the alarm postpone button has been pressed, reset the Elapsed Time Meter. * Check for lamp continuity or if the Elapsed Time Meter reading is 12 or more. Replace lamp if it's open.
  • R
    Richard WatkinsAug 17, 2025
    Why does the breaker repeatedly trip with my Trojan Technologies Water Filtration System?
    • R
      riggsedwardAug 17, 2025
      A repeatedly tripping breaker can be due to a couple of reasons: * The lamp harness may be wet. If so, clean and dry the lamp harness and check the unit for leaks. * There might be a short circuit in the electrical assembly. If this is the case, you should replace the power supply.
  • C
    Cory MartinAug 21, 2025
    What to do if I see a leak from the reactor area of my Trojan Technologies Water Filtration System?
    • H
      hoffmancarolAug 21, 2025
      If you notice a leak from the reactor area, consider these potential causes and solutions: 1. Condensation might be forming on the cold reactor. Try controlling the humidity, relocating the unit, or insulating the reactor. 2. The O-ring at the sleeve bolt could be damaged, deteriorated, or incorrectly installed. Inspect it and replace if needed. 3. The sleeve bolt may not be properly installed. Tighten the sleeve nut finger-tight, then give it an additional 1/5 turn. 4. The O-ring at the UV sensor might be damaged, deteriorated, or incorrectly installed. Inspect and replace it if defective.
  • W
    William RobertsAug 25, 2025
    How to fix a leak at the inlet or outlet of my Trojan Technologies Water Filtration System?
    • M
      Melissa StrongAug 25, 2025
      If you have a leak at the inlet or outlet, here are a couple of things to check: * If the threaded pipe fittings are leaking, clean the threads, reseal them with Teflon tape, and re-tighten. * If the adapter kit is not tight, check the sealing rings and washers.
  • M
    Mary Campbell MDAug 28, 2025
    Why is the green indicator light glowing and the alarm sounding on my Trojan Technologies Water Filtration System?
    • N
      Nathan WallerAug 28, 2025
      If the green indicator light is glowing but the alarm is sounding, it is likely due to an electronic circuit board failure. The suggested solution is to replace the power supply.
  • R
    robbinsstephanieSep 1, 2025
    What to do if the alarm doesn't sound on my Trojan Technologies Water Filtration System?
    • C
      christina03Sep 1, 2025
      If the alarm isn't sounding, it could be due to no power at the AC power outlet. In this case, replace the fuse or reset the breaker.
  • D
    Derek ScottSep 5, 2025
    What to do if a power surge damaged the electrical assembly of my Trojan Technologies Water Filtration System?
    • J
      jessicamcknightSep 5, 2025
      If a power surge has damaged the electrical assembly, the suggested solution is to replace the power supply.
  • T
    Tammy TateSep 9, 2025
    Why is the indicator light not glowing on my Trojan Technologies Water Filtration System?
    • T
      Thomas GreeneSep 9, 2025
      If the indicator light isn't glowing, the unit might be unplugged. Make sure to plug the unit into an AC power outlet.

Summary

SAFETY

Product Specifications

Details the technical specifications and features of different Trojan UVMax™ models.

Troubleshooting Plus and Pro Models

General Safety Warnings

ELECTRICAL SAFETY

GROUNDING

Explains grounding requirements for reducing electrical shock risk.

GROUND FAULT CIRCUIT INTERRUPTER PROTECTION

Details GFCI protection requirements for electrical shock prevention.

EXTENSION CORDS

Provides guidelines for using extension cords with the system.

Parts Included in the TrojanUVMax System

Limited Warranty Coverage

Warranty for Replacement Lamps and Parts

Outlines the warranty terms for replacement lamps and parts.

General Warranty Conditions and Limitations

Specifies general terms, exclusions, and limitations applicable to all warranties.

WATER QUALITY PARAMETERS

REACTOR CHAMBER INSTALLATION

System Installation Guide

INSTALLATION for D, E, F, Pro7 and Pro15 Models

Step-by-step instructions for installing specific UVMax™ models.

INSTALLATION for B & C Models

Step-by-step instructions for installing UVMax™ B & C models.

Cleaning Procedures

Cleaning the Quartz Sleeve

Details how to clean the quartz sleeve to maintain UV intensity.

Cleaning the UV Sensor

Provides instructions for cleaning the UV sensor for accurate readings.

UV Sensor Installation and Removal

UV Sensor Installation

Guides on how to properly install the UV sensor.

UV Sensor Removal

Guides on how to safely remove the UV sensor.

Model Specific Installation Diagrams

Model A 120 V Installation Diagram

Illustrates the installation setup for the Model A (120V).

Model A 230 V Installation Diagram

Illustrates the installation setup for the Model A (230V).

System Operation

Operation for Models A, B, and C

Details operation specifics for Trojan UVMax™ models A, B, and C.

Operation for Models D, E, F, Pro7, and Pro15

Details operation specifics for Trojan UVMax™ models D, E, F, Pro7, Pro15.

Visual and Audible Alarms

Explains the meaning of visual (LED) and audible alarms.

Elapsed Time Meter Function

Describes the function and purpose of the elapsed time meter.

Advanced Operation Features

Alarm Postpone and Re-Set Functions

Covers alarm postponement and elapsed time meter reset procedures.

Dry Contacts and UV Sensor Explanation

Explains system features for external controls and UV intensity monitoring.

Service and Maintenance

Lamp Replacement Procedure

Step-by-step guide for replacing the UV lamp.

Quartz Sleeve Cleaning

Instructions for cleaning the quartz sleeve to maintain performance.

UV Lamp;Sleeve Installation or Replacement

Lamp Removal Steps

Detailed steps for safely removing the UV lamp and sleeve assembly.

Lamp Installation Steps

Detailed steps for safely installing the UV lamp and sleeve assembly.

Trojan Technologies Trojan UV Max Specifications

General IconGeneral
CategoryWater Filtration Systems
ModelTrojan UV Max
TypeUV Disinfection System
Power Supply100-240V / 50-60Hz (Varies by model)
Flow RateVaries by model (see specific model datasheet)
WattageVaries by model (see specific model datasheet)
DimensionsVaries by model (see specific model datasheet)
Inlet/Outlet SizeVaries by model (see specific model datasheet)
Lamp TypeUV Lamp (Low Pressure or Amalgam, varies by model)

Related product manuals