Troy-Bilt 13BC26JD563

Questions and Answers

W
Willie MoralesAug 13, 2025
Why Troy-Bilt Lawn Mower engine fails to start?
- A
  Alicia SmithAug 13, 2025
  The Troy-Bilt Lawn Mower engine may fail to start due to several reasons. It could be that the PTO/Blade is engaged, in which case you should place the blade engage lever in the disengaged (OFF) position. Other potential causes include a disconnected spark plug wire (connect the wire), an empty or stale fuel tank (fill with fresh gas), the choke not activated (place throttle in CHOKE position), a faulty spark plug (clean, adjust gap, or replace), a blown fuse (replace fuse), a flooded engine (crank with throttle in FAST position), parking brake not engaged (engage the parking brake), or the deck chute, mulch plug, or chute tube not properly installed (check their installation).
D
Denise McclainAug 16, 2025
Why Troy-Bilt 13BC26JD563 Lawn Mower engine idles rough?
- C
  Catherine AndersonAug 17, 2025
  A rough idle in your Troy-Bilt Lawn Mower engine can be due to a fouled, faulty spark plug, or one with a gap that's too wide; replace the spark plug and set the plug gap. Also, a dirty air cleaner can cause this issue; replace the air cleaner element and/or clean the pre-cleaner.
M
Michele NobleAug 20, 2025
What to do if Troy-Bilt 13BC26JD563 Lawn Mower engine runs erratic?
- T
  Taylor ClarkAug 20, 2025
  If your Troy-Bilt Lawn Mower engine is running erratically, there are several possible causes. You might have the choke activated (move the throttle control out of the CHOKE position). Check for loose spark plug wires and connect/tighten them. A blocked fuel line or stale fuel could also be the issue, so clean the fuel line, fill the tank with fresh gasoline, and replace the fuel filter. Also, ensure the vent in the gas cap isn't plugged; clear it or replace the cap if damaged. Water or dirt in the fuel system requires draining the tank and refilling with fresh gasoline. Finally, a dirty air cleaner can cause this, so replace the air cleaner paper element or clean the foam pre-cleaner.
S
Sandra ClarkAug 25, 2025
What to do if Troy-Bilt 13BC26JD563 will not mulch grass?
- T
  taylormarcusAug 25, 2025
  If your Troy-Bilt Lawn Mower isn't mulching grass, it could be due to several factors. Ensure the engine speed is high enough by placing the throttle in the FAST (rabbit) position. Avoid mulching when the grass is wet. If the grass is excessively high, mow once at a high cutting height, then mow again at the desired height, or make a narrower cutting swath. A dull blade can also prevent proper mulching, so sharpen or replace the blade.
D
Dawn MccartyAug 28, 2025
Why Troy-Bilt 13BC26JD563 engine overheats?
- S
  Stephen MayAug 28, 2025
  The Troy-Bilt Lawn Mower engine may overheat because the engine oil level is low; fill the crankcase with the proper amount and weight of oil. Another reason could be restricted airflow, so clean grass clippings and debris from around the engine’s cooling fins and blower housing.
V
vwilsonAug 31, 2025
Why Troy-Bilt Lawn Mower has excessive vibration?
- C
  Connor ClarkAug 31, 2025
  Excessive vibration in your Troy-Bilt Lawn Mower can be caused by a loose or unbalanced cutting blade; tighten the blade and spindle, and balance the blade. Another cause could be a damaged or bent cutting blade, in which case you should replace the blade.
N
Natalie FullerSep 4, 2025
How to fix uneven cut with Troy-Bilt 13BC26JD563 Lawn Mower?
- G
  gregorymilesSep 4, 2025
  An uneven cut with your Troy-Bilt Lawn Mower can result from a deck that isn't leveled properly; perform a side-to-side deck adjustment. A dull blade can also cause this, so sharpen or replace it. Finally, check the tire pressure in all four tires, as uneven pressure can lead to an uneven cut.
D
donaldwilliamsSep 8, 2025
Why Troy-Bilt Lawn Mower engine hesitates at high RPM?
- C
  Christopher BrownSep 8, 2025
  If your Troy-Bilt Lawn Mower engine hesitates at high RPM, it might be because the spark plug gap is too close. Remove the spark plug and reset the gap.

Troy-Bilt 13BC26JD563 Specifications

General

Brand	Troy-Bilt
Model	13BC26JD563
Engine Displacement	190cc
Cutting Positions	6
Mulch Capable	Yes
Side Discharge	Yes
Rear Bag	Yes
Bagging Capability	Yes
Starter Type	Recoil
Speed Settings	Variable
Deck Material	Steel
Engine	Briggs & Stratton
Engine Type	4-Cycle
Cutting Width	21 in
Cutting Height	1.25 - 3.75 in
Grass Discharge	Side discharge
Wheel Size - Front	8 in