Troy-Bilt 52063, 52064

Questions and Answers

V
Valerie YoungAug 14, 2025
Why Troy-Bilt 52063, 52064 engine does not start?
- J
  Jeffrey LevineAug 14, 2025
  If your Troy-Bilt Trimmer engine won't start, there are several potential causes: * The spark plug wire may be disconnected, so reconnect it. * The spark plug could be defective or incorrectly gapped, so inspect or replace it. * The fuel tank might be empty, so add fuel. * The carburetor or fuel line could be dirty, so clean them. * The air cleaner could be dirty, so clean or replace it. * The carburetor might be out of adjustment. * The engine might be flooded, so wait several minutes before starting. * The engine throttle lever might be in the incorrect position, so move it to the FAST position. * The gasoline could be stale, so drain the old fuel and add fresh fuel.
X
xwaltersAug 17, 2025
How to fix Troy-Bilt Trimmer engine that runs poorly?
- M
  michael70Aug 17, 2025
  If your Troy-Bilt Trimmer engine runs poorly, consider these potential causes: * A bad spark plug: Inspect or replace the spark plug. * A dirty air filter: Clean or replace the air filter. * Stale fuel: Drain the old fuel and replace it with fresh fuel. * Engine cooling system clogged: Clean the fins.
R
Raymond MillerAug 21, 2025
What to do if electric starter of Troy-Bilt 52063, 52064 Trimmer does not start engine?
- A
  Anita JonesAug 21, 2025
  If the electric starter on your Troy-Bilt Trimmer (electric start models only) doesn't start the engine, consider these possibilities: * Wires to the battery may be unconnected: Reconnect the wires. * The battery may not be charged: Charge the battery. * There may be a broken wire in the wiring harness: Replace the wiring harness.
A
Anna PhelpsAug 25, 2025
What to do if Troy-Bilt 52063, 52064 vibrates too much?
- T
  tony20Aug 25, 2025
  If your Troy-Bilt Trimmer is vibrating, several issues could be the cause: * The trimming head mounting bolt might be loose, so tighten it. * The line lengths may be substantially different, so adjust the lines to approximately equal lengths. * There might be loose nuts or bolts, so check all bolts and nuts, including engine bolts. * The spindle head or trimmer head could be broken, so replace the broken part.
I
Isabella BrownAug 27, 2025
Why is my Troy-Bilt Trimmer engine overheating?
- K
  Kimberly Rice DDSAug 27, 2025
  If your Troy-Bilt Trimmer engine overheats, it could be due to: * A clogged engine cooling system. Clean the air cooling areas and behind the debris shield.
V
vfloresAug 31, 2025
How to improve mowing performance of Troy-Bilt 52063, 52064 Trimmer?
- J
  Jeffrey BrownAug 31, 2025
  Poor mowing performance with your Troy-Bilt Trimmer can be due to: * Line length being too short or too long: Adjust the line length to 18" long. Replace the line when it's less than 1/2 this length. * Cutting height being too high or low for the grass: Adjust the cutting height to approximately 1/3 of the length of the grass. * Engine not set at FAST speed: Move the Engine Throttle Lever to FAST (Rabbit).
M
Mario WatsonSep 3, 2025
Why Troy-Bilt 52063, 52064 Head does not retain height setting?
- J
  Joshua ThorntonSep 3, 2025
  If the Troy-Bilt Trimmer head does not retain height setting, it could be due to: * Loose head bolts: Tighten the head bolts to 75 in/lbs. * A worn head: Replace the head assembly.
B
Bradley RiceSep 6, 2025
Why Troy-Bilt Trimmer battery does not charge during engine operation?
- S
  Shawn HaynesSep 6, 2025
  If your Troy-Bilt Trimmer battery does not charge during engine operation (electric start models), it could be due to: * A dead battery: Replace the battery.
T
Tony CainSep 10, 2025
What to do if Troy-Bilt 52063, 52064 battery charger does not charge battery?
- R
  Rachel LeonardSep 12, 2025
  If your Troy-Bilt Trimmer battery charger does not charge the battery (electric start models), it could be due to: * A broken battery lead: Replace the battery lead. * A broken battery charger wire: Replace the battery charger. * A dead battery: Replace the battery.