TruXedo Truxport - User Manual

Owners & Installation Manual
READ INSTRUCTIONS - Failure to assemble cover
properly will void warranty.
1. Do not place objects on or against cover or framework.
2. Do not tie cargo to TruXport framework.
3. Never allow children or pets to occupy pickup box while
cover is closed.
4.
5.
6.
Cover is not airtight. Special care is required to keep
cargo clean and dry.
Fabric cover won’t prevent theft of contents inside truck
box.
Cover must be rolled fully open and secured with
retainer straps when towing vehicle backwards.
7. Rolled opened cover must be tightly rolled, securely
cinched down with both retainer straps, and away from
the cab and window. DO NOT STOW COVER
AGAINST TRUCK CAB OR BACK WINDOW.
8. Cover must be rolled fully open and secured with
retainer straps if any part of the truck bed cover is worn
or damaged.
SAFETY INSTRUCTIONS
Warranty registration must be on file
and/or proof of original purchase (detailed
and dated receipt) required for warranty
to be effective.
Register online at www.truxedo.com.
• Always wear safety glasses and/or other necessary protective
equipment when installing your TruXport
®
.
• T
hese instructions are complete for most pickup models.
A
dditional instr
uctions are included, if required for your pickup.
Please read entire manual before installing your TruXport
®
.
COVER MAINTENANCE
V
i
n
y
l
c
o
v
e
r
c
a
n
b
e
h
a
n
d
w
a
s
h
e
d
w
i
t
h
m
i
l
d
s
o
a
p
a
n
d
w
a
t
e
r
o
r
cleaned
in
a
car
wash.
Thoroughly
rinse
cover
to
remove
any
soap
residue.
Recommended
to
use
the
tested
and
approved
Protex
truck
bed
cleaner
or
any
vinyl
protectant
made
for
truck
bed
covers
.
Never
use
any
vinyl
conditioners
(
ie,
Armor
All®)
t
h
a
t
c
o
n
t
a
i
n
s
i
l
i
c
o
n
e
,
p
e
t
r
o
l
e
u
m
,
o
r
c
i
t
r
u
s
b
a
s
e
d
products
on
your
truck
bed
cover
as
they
may
crack and shrink the vinyl.
FIV
E YEAR WARRANTY
TruXedo, Inc. warrants that all new, unused products are free
from defects in material and workmanship. This Five Year Limited
Warranty is effective if the product is properly installed and used
for the purpose intended. It applies to the original buyer only.
TruXedo’s obligation under this Warranty is limited to repairing,
or at its option, replacing any part that is returned, transportation
prepaid, to TruXedo, Inc., Yankton, South Dakota, if the product is,
in our judgment, defective. All materials must be accompanied by
an RMA (Returned Material Authorization) number requested by
and authorized in advance of returning the materials. TruXedo, Inc.
shall not be liable or responsible to supply or pay labor to replace
any part found defective, nor shall it be liable for any damages of
any kind or nature to person, product, or property.
There are no Warranties for used products or products that have
been repaired, altered, modified, subjected to misuse, negligence,
accident or ordinary wear and tear. Warranty registration must be on
file and/or proof of original purchase (detailed and dated receipt)
required for warranty to be effective .
Register online at www.truxedo.com
Questions?
Call our friendly customer service staff
at TruXedo, Inc. Toll Free:
1-877-878-9336
Mon - Fri 8 am - 5 pm CT
OWNER/USER RESPONSIBILITIES
It is the responsibility of the owner/user to read this manual and
comply with the operating procedures. The owner/user is also
responsible for inspecting their TruXport
®
cover, and for having
parts repaired or replaced when worn or damaged.
Failure to follow safety instructions and warning labels could result
in failure of your cover system and/or personal injury.
MESSAGES TO INSTALLER
WARNING
Tighten clamps securely on side rails before driving
vehicle, to prevent cover from blowing off.
!
P/N 1118257, Rev A

Summary

Five Year Warranty

Safety Instructions

Messages to Installer

RamBox Bed Install

Bulkhead Seal Installation

Install the bulkhead seal to the top of the bulkhead, cleaning the surface with rubbing alcohol before application.

RamBox Bed Install

For RamBox installs, adhere a foam block onto the face of the bulkhead, fitting tightly in the corner with the bed cap.

Corner Seal Installation

Place corner seals onto both cab end corner plugs, noting the small notch differentiating them from tailgate end seals.

Rail and Cover Installation

Assemble on a flat surface and insert cover rails into the header rail in the rolled assembly prior to installing.

Rail Bracket Installation

Rail Mounting Brackets

Slide rail mounting brackets into rails at opposite ends, with square head bolts in the upper slot at the front/cab end.

Lower Bracket Attachment

Slide the lower half of the bracket into the RamBox rail from the rear/tailgate end, then secure with bolts.

Tailgate Corner Seal Installation

Closing the Cover

Hook and Loop Fasteners

Secure hook and loop fasteners along the full length of both side rails to complete cover closing and prevent wind lift.

Cover Tension

Opening the Cover

Replacement Parts

Overview

1. Function Description
2. Usage Features
3. Maintenance Features

The TruXport is a soft roll-up truck bed cover designed to protect cargo in the truck bed from the elements and provide a secure storage space. It is specifically designed for RamBox installations, with detailed instructions for proper fitting and use.

Function Description:

The primary function of the TruXport cover is to provide a protective barrier over the truck bed. When closed, it helps to keep cargo clean and dry by shielding it from rain, snow, and dust. The roll-up design allows for full access to the truck bed when needed, making it versatile for various hauling needs. The cover is not airtight, so while it offers significant protection, users should be aware that some moisture or fine dust may still enter the bed. It also does not prevent theft of contents, as the fabric cover is not designed for high-security protection.

Usage Features:

• Installation: The TruXport cover requires a multi-step installation process. It begins with installing a bulkhead seal and foam block at the front of the truck bed, followed by corner seals on both the cab and tailgate ends. The cover rails are then inserted into the header rail of the rolled assembly. The entire cover assembly is lifted onto the existing cargo rails, with the bottom of the cover rail fitting into the top slot of the cargo rails. It is then slid forward until the cab rail seals make good contact with the bulkhead seals, and the cover is centered side-to-side. RamBox brackets are installed at opposite ends of the rails, sliding into the cover rail and the RamBox rail, and then tightened to secure the cover. Finally, tailgate corner seals are placed on the cover header panel.
• Opening the Cover: To open the cover, the tailgate must be open. The user presses downward on one side latch to disengage it, then grasps the tailgate header to release the opposite latch. The cover can then be rolled up towards the cab. It is important not to disengage the hook and loop fasteners prior to rolling the cover.
• Securing the Open Cover: When the cover is fully rolled up, it must be tightly rolled, securely cinched down with both retainer straps, and positioned away from the cab and window. A critical safety instruction is DO NOT STOW COVER AGAINST TRUCK CAB OR BACK WINDOW. This ensures visibility and prevents potential damage. If any part of the truck bed cover is worn or damaged, it must be rolled fully open and secured with retainer straps.
• Closing the Cover: To close the cover, the retainer strap hooks are released, and the cover is unrolled over the truck bed. Each of the bows will sit on top of the rails. With the tailgate open, the tailgate header is hooked into the header stops on both sides of the truck. The tailgate header is then pushed down until the latches on both sides engage with the tailgate header, providing an audible click when fully engaged. To prevent wind lift, the hook and loop fasteners along the entire length of both side rails must be secured by pressing firmly.
• Cover Tension: The latch assembly is factory set to the correct tension, and there is no need to adjust it. Any modification to the latch will void the warranty. To maintain cover tautness, users should periodically repeat the steps for securing the hook and loop fasteners and re-stretching the cover across the bed.
• Cargo Management: Users are explicitly warned not to place objects on or against the cover or its framework, nor to tie cargo to the TruXport framework. This prevents damage to the cover and ensures safe operation.
• Safety Precautions: Children or pets should never be allowed to occupy the pickup box while the cover is closed. When towing the vehicle backwards, the cover must be rolled fully open and secured with retainer straps. Clamps on the side rails must be tightened securely before driving to prevent the cover from blowing off.

Maintenance Features:

• Cleaning: The vinyl cover can be hand washed with mild soap and water or cleaned in a car wash. It should be thoroughly rinsed to remove any soap residue. The manual recommends using tested and approved Protex truck bed cleaner or any vinyl protectant specifically made for truck bed covers. A crucial warning is Never use any vinyl conditioners (e.g., Armor All®) that contain silicone, petroleum, or citrus-based products on your truck bed cover as they may crack and shrink the vinyl.
• Latch Maintenance: For continued ease of operation, the hook and loop fasteners and the latch should be periodically cleaned with high-pressure water to remove dirt and dust.
• Inspection: The owner/user is responsible for regularly inspecting their TruXport cover and having parts repaired or replaced when worn or damaged.
• Warranty: The TruXport comes with a Five Year Limited Warranty covering defects in material and workmanship for new, unused products, provided it is properly installed and used as intended. The warranty applies to the original buyer only. Warranty registration must be on file, and proof of original purchase (a detailed and dated receipt) is required for the warranty to be effective. Registration can be done online at www.truxedo.com. The warranty does not cover used products, or products that have been repaired, altered, modified, subjected to misuse, negligence, accident, or ordinary wear and tear.

The TruXport is designed for ease of use and durability, providing a practical solution for truck bed protection with clear guidelines for installation, operation, and maintenance.

TruXedo Truxport Specifications