To Next PageTo Next Page
Need help?Do you have a question about the UEi DL579 and is the answer not in the manual?
General| Brand | UEi |
|---|---|
| Model | DL579 |
| Category | Measuring Instruments |
| Language | English |
Lists primary measurement capabilities like True RMS, voltage, current, capacitance.
Includes NCV, Inrush, Temperature, Low Z, Diode, Continuity.
Covers frequency and duty cycle measurement functions.
Details resistance and capacitance measurement functions.
Dual display, backlight, auto/manual ranging.
Data Hold, Auto Power Off, test lead storage.
Visible high-voltage alert, magnetic mount, input jack locks.
Specifies operating/storage temperature and humidity.
Covers display, dimensions, weight, CAT rating, certifications.
Information on battery type and test leads.
General warnings for safe operation, service, and voltage handling.
Instructions for pre-use verification and safe test lead usage.
Precautions for storms, wet conditions, PPE, and circuit safety.
Awareness for high energy, and response to electrical incidents.
Safety procedures tailored for HVAC/R technicians.
Displays common symbols for measurements and units.
Shows symbols indicating warnings, dangerous levels, or safety.
Defines safety categories for building installations and their typical short-circuit values.
Describes the clamp, alignment marks, and lever operation.
Explains category indicators, NCV light, and rotary dial.
Details input jacks, wire separation, and test lead holder.
Explains the operation of Range, SELECT, and HOLD/Backlight buttons.
Describes Min/Max button functionality and display characteristics.
Explains the operation of the Inrush/Hz Duty button.
Details temperature probe inputs and input jack lock switch.
Describes the built-in magnet, strap, and battery cover.
Details how to operate the meter in Low Z mode.
Lists features specific to the Low Z measurement function.
Explains how to measure AC Amps using the clamp jaw.
Provides range, resolution, accuracy, and overload protection.
Offers tips for accurate AC Amps measurement.
Identifies the NCV sensor and details how to perform detection.
Notes factors affecting NCV detection accuracy and reliability.
Explains the behavior of the voltage indicator light.
Lists features related to Non-Contact Voltage detection.
Details how to set up the meter for microamp measurements.
Provides accuracy and overload protection for DC and AC microamps.
Warns against exceeding the specified microamp measurement limit.
Details how to set up the meter for temperature readings.
Specifies the need for K-Type thermocouple probes.
Provides accuracy and overload protection for temperature readings.
Clarifies that stated accuracy excludes thermocouple accuracy.
Explains how to perform a continuity test.
Specifies the threshold for the continuity buzzer and warns against live circuits.
Details how to set up the meter for resistance measurements.
Lists resistance ranges, resolution, accuracy, and overload protection.
Warns against measuring resistance on live circuits.
Explains how to set up the meter for capacitance measurements.
Lists capacitance ranges, resolution, accuracy, and overload protection.
Warns about safely discharging capacitors before measurement.
Explains how to perform a diode test and interpret readings.
Provides open circuit voltage, test current, and overload protection.
Details how to set up the meter for AC voltage measurements.
Lists AC voltage ranges, resolution, accuracy, and overload protection.
Explains high voltage indicator and audible alerts for AC measurements.
Warnings for test lead rating and measurement limits for AC voltage.
Details how to set up the meter for DC voltage measurements.
Lists DC voltage ranges, resolution, accuracy, and overload protection.
Explains high voltage indicator and audible alerts for DC measurements.
Warnings for test lead rating and measurement limits for DC voltage.
Details how to set up the meter for frequency measurements.
Lists frequency ranges, resolution, accuracy, and overload protection.
Details how to set up the meter for duty cycle measurements.
Lists duty cycle accuracy and overload protection.
Warns about test lead rating and voltage limits for frequency.
Details how to set up the meter for LRA Inrush current measurement.
Explains the steps to capture and read inrush current.
Provides guidance on selecting ranges for inrush measurements.
Details measurement locations for CAT IV and CAT II leads.
Explains the importance of CAT IV shields and when they can be removed.
Warns not to confuse lead rating with meter rating.
Advises on using compliant replacement test leads.
Step-by-step guide for replacing the meter's batteries.
Details the warranty period and what is covered.
Outlines what the warranty does and does not cover.
Provides contact details for warranty and service inquiries.
Explains the symbol for separate collection and correct disposal.
Provides instructions for cleaning the meter's case.
Warns against using abrasive liquids or strong detergents.
Recommends battery removal and environmental conditions for storage.
