What to do if my Uniden Scanner won't start scanning?
If your Uniden Scanner won’t start scanning, here are a few things to try: 1. Press the Scan button. 2. Adjust the squelch threshold. 3. Ensure the channels you want to scan are not locked out. 4. Check the antenna connection.
How to fix a Uniden UBC69XLT-2 that won't stop scanning?
If your Uniden Scanner won’t stop scanning, consider these potential solutions: * Adjust the squelch threshold. * Check the antenna connection. * Make sure the channels you want to scan are not locked out. * Ensure the channel’s frequency is stored in the scanner’s memory. * Wait for a transmission on the channel, as it might not be active.
Why is the reception bad on my Uniden UBC69XLT-2 Scanner?
If you are experiencing improper reception on your Uniden Scanner, try the following: * Check the antenna connection, move, or reposition the antenna. * Move the scanner to a different location. * If you are in a remote area, you might need an optional multi-band antenna. Check with your dealer or local electronics store.
Use only genuine Uniden earphones to avoid hearing damage and adjust volume properly.
This unit is not waterproof; avoid exposing it to rain or moisture to prevent fire or shock.
Connects to the scanner for receiving signals. Refer to Page 17 for details.
Port for private listening with earphones or headphones.
Adjusts sensitivity to reduce or eliminate background noise.
Adjusts the audio output level of the scanner.
Shows the scanner's current operating status and information.
Buttons used for operating the scanner functions and programming.
Turns the scanner on or off.
Instructions on how to switch between band plans 1, 2, and 3.
Search through personal bands in 5 locations, chaining frequency bands.
Eliminates IF images for clearer reception of selected frequencies.
Delays scanning for 2 seconds to catch replies on the same channel.
Skip specified channels/frequencies during scanning or searching.
Program one channel to check every 2 seconds during scans.
Lock scanner keys to prevent accidental changes to programming.
Allows direct access to any channel.
Improves readability of the display in low-light conditions.
Provides good reception and prevents breakage; allows external antenna connection.
Retains stored frequencies even when power is lost.
Scanner sounds tones for correct operations and errors.
Warns the user when battery power is low.
Guidance on using the manual and initial setup steps.
Explains how the scanner finds and stays on active frequencies.
Explains searching for unprogrammed active frequencies.
Describes systems using a single frequency for simplex or repeater systems.
Details single-frequency operation, typically line-of-sight.
Explains two-frequency systems using a central repeater for wider coverage.
Suggests the internet as a source for frequencies and scanning information.
Guides users on finding frequencies and agencies online.
Tips for improving reception, using accessories, and avoiding harsh environments.
Instructions on how to install the two AA batteries.
Advice on using fresh batteries, replacement, and removal to prevent damage.
Steps to attach the supplied flexible antenna to the BNC connector.
How to connect earphones/headphones and extension speakers.
Instructions for attaching the belt clip for easier carrying.
Explains basic terms like frequency, channel, and tuning.
Details the functions of the scanner's keys.
Explains the primary and secondary functions of various keys.
Explains the indicators and symbols shown on the scanner's display.
Steps to power on the scanner and adjust squelch for clear reception.
Procedure to enter and save frequencies into memory channels.
How to search for and save active frequencies found.
How to start scanning through programmed channels.
Important notes on scanning, including when it won't scan.
How to monitor a single channel without scanning or pause scanning.
Feature to search through preset or custom frequency ranges.
Covers chain search mode and hold mode.
How to save frequencies found during chain search into memory channels.
How to define the lower and upper limits for each search bank.
How to skip specified frequencies during a search.
Notes on skipping frequencies, including limits and selection.
How to program a 2-second delay to avoid missing replies.
How to activate and turn off the delay feature during scanning or searching.
How to skip channels with continuous transmissions.
How to program a channel to be checked periodically during scans.
Steps to select a different channel as the priority channel.
How to lock and unlock the scanner's keys to prevent accidental changes.
How to turn on the display backlight for better visibility.
Possible causes and suggestions for when the scanner does not work.
Solutions for poor reception, including antenna adjustment and location.
Reasons why the scanner might not stop scanning and how to fix it.
Causes and solutions for when the scanner fails to start scanning.
Procedure to reset the scanner when it locks up or malfunctions.
Guidelines for general operation, power disconnection, and memory management.
Advice on where to use and avoid placing the scanner.
Instructions for cleaning the scanner and note on non-serviceable parts.
Explanation of birdies and how to lock them out.
Details on channel count and frequency ranges covered.
Includes sensitivity, scan rate, search rate, and delay.
Details on audio output, speaker, and current drain.
Covers power requirements, jacks, size, and weight.
Identifies the manufacturer and declares compliance with EU directives.
To Next Page
General