Need help?Do you have a question about the Uniden UBCD396XT and is the answer not in the manual?
General| Weather Alert | Yes |
|---|---|
| PC Connectivity | USB |
| Type | Handheld Scanner |
| Modulation | AM, FM |
| Memory | Dynamic Memory Allocation |
| Display | Backlit LCD |
| Battery Type | AA Alkaline or Rechargeable Ni-MH |
| Bands | VHF, UHF, 700 MHz, 800 MHz |
| GPS | Yes |
| Trunking | APCO 25 Digital Trunking, Motorola, EDACS, LTR |
| Frequency Range | 25-512 MHz |
Detailed steps for correctly installing alkaline or NiMH batteries into the scanner.
Instructions on how to connect the scanner's internal or external antenna.
Guide on how to attach and remove the belt clip for portable use.
Diagram and instructions for physically connecting a GPS receiver to the scanner.
Scanner operation for checking programmed frequencies or Talk Group IDs.
Scanner operation for checking frequencies within a programmed range.
Scanner stays on the current channel, enabling save and edit options.
Scanner interrupts operation to check for strong nearby signals.
Scanner performs only Close Call checks, stopping all other scanning.
Scanner performs Close Call checks without interrupting audio.
Scanner pauses operation at intervals to check priority channels.
Scanner stops operation to check only priority channels.
Scanner displays longitude, latitude, and heading information.
Scanner checks channels for specific paging tones.
Scanner searches frequency ranges and displays signal strength visually.
Explanation of basic key press actions: tap, double tap, press & hold, and FUNCTION combinations.
Instructions on navigating and selecting options within the scanner's menu system.
Step-by-step guide to creating and configuring a conventional radio system.
Guide to programming an EDACS SCAT type system.
Instructions to create a site for an EDACS SCAT system.
Steps to add at least one frequency to an EDACS SCAT system's site.
Guide to programming EDACS Wide or Narrow trunked systems.
Instructions to create a channel group for scanning in an EDACS system.
Steps to add channels to a channel group in an EDACS system.
Guide to programming an LTR trunked system.
Steps to add channels to a channel group in an LTR system.
Guide to programming Motorola trunked systems (VHF, UHF, 800 MHz).
Description of the 16 pre-programmed fleet maps available for selection.
Guide to programming a custom fleet map by selecting size codes for blocks.
Guide to programming standard Project 25 (P25) trunked systems.
Instructions to create a site for a P25 trunked system.
Steps to add frequencies to a P25 trunked system's site.
Steps to add channels to a channel group in a P25 system.
Guide to programming single-frequency P25 systems.
Instructions to create the single site for a P25 system.
Steps required to program a system for scanning.
Instructions to create a channel group for scanning in a P25 system.
Steps to add channels to a channel group in a P25 system.
Describes the typical communication process in a trunked radio system.
Method for setting location centers based on jurisdictional boundaries.
Method for setting location centers based on physical antenna locations.
Strategy to combine geopolitical and antenna-centric approaches for optimal scanning.
Instructions for assigning number tags at system or channel levels.
Details on assigning System Number Tags (SNTs) from 0 to 999.
Details on assigning Channel Number Tags (CHNTs) from 0 to 999.
Guide on how to use number tags for direct navigation to systems or channels.
Instructions for programming Quick Keys (SQK, GQK) to enable/disable systems/groups.
Details on assigning System/Site Quick Keys (SQKs) from 0 to 99.
Details on assigning Group Quick Keys (GQKs) from 0 to 9.
Instructions on how to use Quick Keys in Scan mode.
Guide to assigning search ranges (service, custom, tone-out, band scope) to keys.
Instructions on activating a search by pressing a programmed Search Key.
Steps to configure geographic information for a system site.
Steps to configure geographic information for a channel group.
Instructions for programming points of interest, roads, and intersections.
Detailed steps to create a new location (POI, Xing, Road) with name, coordinates, and alerts.
Explains settings for dangerous crossings and roads, including heading and speed limits.
Instructions for modifying the settings of a previously programmed location.
How to configure system-level alerts for emergency flags.
How to configure alerts for Close Call hits.
How to configure alerts for hits on Tone-Out channels.
How to configure alerts for approaching programmed locations.
Explanation of Quick Keys for enabling/disabling systems and groups during scans.
Explanation of Startup Keys for locking/unlocking systems, sites, and searches at power-up.
Explanation of Search Keys for quickly starting programmed searches.
Steps to configure up to 10 channels for paging tone monitoring.
Instructions on how to start and use the Tone-Out search feature.
Details key operations for navigating and controlling Tone Out mode.
Details key operations specific to Close Call Only mode.
Instructions on how to activate Band Scope mode using Search Key 3.
Details key operations for navigating and controlling Band Scope mode.
Details key operations for navigating and controlling GPS mode.
Menu to set various options for each system.
Menu to create or edit sites within trunked systems.
Menu to create or edit channel groups within a system.
Sets whether to scan programmed IDs or all found IDs.
Enables or disables checking priority channels in Priority ID Scan mode.
Configures scanner alerts for detected emergency flags in Talk Groups.
Selects the Talk Group ID format (Decimal, Hexadecimal, or AFS).
Allows selection or programming of Motorola fleet maps.
Determines whether to check or ignore the status bit in Talk Group IDs.
Configures end transmission code recognition for channel leaving.
Menu to program channel information for this group.
Limits reception to transmissions with a specific Network Access Code (NAC).
Configures P25 wait time to prevent false decodes on mixed signals.
Assigns a Quick Key to enable/disable the search range during scanning.
Assigns a Startup Key to lock/unlock the search range at power-up.
Assigns a number tag for quick access to the search range.
Determines if the search range should be ignored during Scan/Search modes.
Sets how long the scanner checks the search range before moving to the next.
Instructions for assigning Startup Keys (0-9) to systems, sites, or search ranges.
Configures the 10 tone-out channels with frequency, tone, and options.
Option to enter or edit the name of a tone-out channel.
Sets the wait time before moving to the next channel after a transmission ends.
Configures Automatic Gain Control for the Tone-Out channel.
To Next Page
