How to clear lubrication time on UNITY LAUNDRY SYSTEMS UTS62?
The run times on the UNITY LAUNDRY SYSTEMS Laundry Appliance can be viewed and cleared by pressing the [START] button for 3 seconds from the startup screen.
How to fix DoorStat Error on UNITY LAUNDRY SYSTEMS UTS62 Laundry Appliance?
If you encounter a DoorStat Error on your UNITY LAUNDRY SYSTEMS Laundry Appliance, check the door switch or door pin.
What to do if UNITY LAUNDRY SYSTEMS Laundry Appliance shows overtime of fill?
If your UNITY LAUNDRY SYSTEMS Laundry Appliance is experiencing overtime of fill, check the fill valve and the level sensor.
How to troubleshoot overtime of drain in UNITY LAUNDRY SYSTEMS Laundry Appliance?
If your UNITY LAUNDRY SYSTEMS Laundry Appliance shows overtime of drain, check the drain valve.
What to do for high temperature of inverter in UNITY LAUNDRY SYSTEMS UTS62?
If your UNITY LAUNDRY SYSTEMS Laundry Appliance shows a high temperature for the inverter, clean the lint inside the machine and check the inverter fan.
How to resolve Invt comm overtime on UNITY LAUNDRY SYSTEMS UTS62?
If your UNITY LAUNDRY SYSTEMS Laundry Appliance is showing an Invt comm overtime error, check the power inverter and the inverter's parameters.
How to troubleshoot overtime of heat error in UNITY LAUNDRY SYSTEMS UTS62 Laundry Appliance?
If your UNITY LAUNDRY SYSTEMS Laundry Appliance displays an overtime of heat error, examine the heating device and check the temperature sensor.
What to do if UNITY LAUNDRY SYSTEMS UTS62 Laundry Appliance displays an inverter error?
If your UNITY LAUNDRY SYSTEMS Laundry Appliance shows an inverter error, check the inverter itself and its input power.
How to fix door leakage in my UNITY LAUNDRY SYSTEMS Laundry Appliance?
If you're experiencing door leakage, start by checking if the door is tight. Adjust the door hinges if necessary. If the door gasket is damaged, replace it. Misalignment can also cause leaks, so check and adjust the door hinges.
Why is my UNITY LAUNDRY SYSTEMS Laundry Appliance vibrating excessively during high extract?
Excessive vibration during high extract can occur for several reasons. First, check if the transport brackets have been removed. If not, remove them. Ensure the machine is level. Also, the out-of-balance switch might be malfunctioning, so check it and replace it if necessary. Make sure the load is between 7-35 lbs. Damaged shock absorbers may also cause this issue, so replace them if needed.
General| Brand | UNITY LAUNDRY SYSTEMS |
|---|---|
| Model | UTS62 |
| Category | Laundry Appliance |
| Language | English |
Explains DANGER, WARNING, CAUTION, IMPORTANT, and NOTE statements used in the manual.
Crucial safety precautions for washer operation, installation, and maintenance.
Describes safety decals on the machine for hazard identification and warnings.
Guidelines for safe operation and daily checks to prevent injury during use.
Details on the function, placement, and responsibility for the emergency stop device.
Procedure for inspecting the machine upon delivery for shipping damage.
Identifies the location of the serial plate for warranty and assistance purposes.
Lists included accessories such as manuals, warranty card, and parts.
Contact information for technical assistance and ordering replacement parts.
Technical details and specifications for the UTS40 washer model.
Diagrams and measurements detailing the physical dimensions of the UTS40 machine.
Technical details and specifications for the UTS62 washer model.
Diagrams and measurements detailing the physical dimensions of the UTS62 machine.
Minimum clearances required for proper installation and maintenance access.
Specifies the need for a level, strong floor for stable machine installation.
Step-by-step instructions for connecting the water supply to the washing machine.
Procedures and diagrams for connecting the machine's drain system according to codes.
Safety warnings and requirements for electrical connections and grounding.
Details on electrical connection types, wiring diagrams, and required codes.
Instructions for manual and external dosing of chemicals into the machine.
Procedure for removing shipping brackets and door cable for the UTS40 model.
Procedure for removing shipping brackets and door cable for the UTS62 model.
Overview of the controller for the vended market, including button functions and navigation.
Overview of the controller for the on-premise market, including button functions and navigation.
Describes the initial startup interface and sequence of the washer.
Displays the idle interface of the controller after the startup sequence.
Explains how to start and monitor automatic wash cycles on the controller.
Instructions on how to access and view machine cycle counts and statistics.
Details on checking and clearing recorded data like total run counts.
Procedure for changing user passwords for accessing the controller interface menus.
Guide to setting prices for various wash programs on vended models.
Steps to set standard, special day, or special hour prices for wash cycles.
Instructions for setting the machine's current system time and date.
Information on pre-programmed wash cycles and how to edit them.
How to access and navigate the programming mode interface and enter the password.
Steps to select, add, or delete steps within a wash program.
Procedure for saving modified wash programs or exiting without saving.
How to handle and clear alarm signals from the controller using the start button.
Table of common alarms, their names, and troubleshooting steps.
Lists and describes Variable Frequency Drive (VFD) alarms and remedies.
How to access and view the alarm log interface on the controller.
Guide to finding the USB port and inserting a USB flash drive into the machine.
Steps to upload machine parameters from a USB drive to the controller.
Procedure to upload wash programs (formulas) from a USB drive to the controller.
Procedure to download machine parameters from the controller to a USB drive.
Procedure to download wash programs (formulas) from the controller to a USB drive.
Steps to update the machine's software using a USB flash drive.
Procedure to upload PUNP VFD parameters from a USB drive to the washer.
Procedure to download PUNP VFD parameters from the washer to a USB drive.
Lists alarms and troubleshooting steps specific to USB operations.
Details the specifications for the coin mechanism, focusing on coin size range.
Provides mechanical dimensions and diagrams of the coin mechanism.
Explains the function of switches, buttons, and connection ports on the coin mechanism.
Details the menu structure for configuring the coin mechanism's settings.
Step-by-step guide for teaching the coin acceptor a specific coin value.
Guide on how to change the price for wash cycles using the coin mechanism.
Procedure to change the recognized coin value for specific channels.
How to adjust coin acceptance tolerance for better accuracy and forgery rejection.
Steps to delete predefined coin settings for specific channels.
Explains the relationship between coin value, price, and pulse output.
Common issues and solutions for the coin mechanism.
Recommendations for cleaning and maintaining the coin acceptor.
Daily checks and cleaning procedures for the machine, including door interlock.
Weekly checks for leaks and cleaning of lint inside the machine.
Monthly checks including belt alignment and pulley verification.
Quarterly checks like tightening hinges, anchor bolts, and checking bearings.
Explanation of the out-of-balance protection feature and its operation.
Information regarding VFD parameters, status, and error codes.
Comprehensive guide to diagnose and resolve machine failures by failure type.
To Next Page
