Uponor T-75 - Settings Menu Functions

www.uponor-usa.com • www.uponor.ca
30
Uponor Climate Co˘ntrol™ Zoning System Installation Guide
31
ECO Night and Day
For example:
ECO mode active:
From 10:30 p.m. to 5 a.m.
From 9:30 a.m. to 2:30 p.m.
ECO Night
For example:
ECO mode active:
From 10:30 p.m. to 5 a.m.
ECO Custom
For example:
ECO mode active:
From 12:30 a.m. to 5:30 a.m.
From 12:00 a.m. to 5:30 p.m.
• Displaying the proles:
Comfort or ECO mode off.
Economy or ECO mode on.
• All proles can be modied.
• All customized settings remain saved in the event of
a power failure.
Editing the ECO Proles
1. Uponor screen > Main Menu > Settings
> Edit ECO Proles
2. Select the ECO prole to modify.
> Press OK.
3. Modify the heating prole.
> Press OK.
4. To modify the prole:
• Select the time using the
and keys. The cursor
moves by increments of 30 minutes. The set time is
indicated above the time prole.
• Apply the Comfort mode by pressing the
key.
• Apply the ECO mode by pressing the
key.
5. To set a complete period within the same mode:
• Move the cursor to the start time of the period.
• Set the start time: Press briey the or key.
• Move the cursor to the end time of the period.
• Press and hold the
or key.
The prole applies for the whole period from start time
to end time.
6. Modify the correction value of
the temperature setpoint for the
ECO mode.
> Press OK.
Apply ECO Proles
1. Uponor screen > Main Menu > Settings > Rooms >
Apply ECO Proles.
2. Select the desired base unit or
all base unit (only applies if more
than one base unit is installed).
> Press OK.
3. Select the desired room or All.
> Press OK.
Select the day:
Go to the day by using the
and
keys and select the day by briey
pressing the
key.
4. The present prole is displayed
5. Select the ECO Proles mode:
Press and hold
.
6. Select the desired ECO Prole.
> Press OK.
7. Repeat for each day.
To check the setting for a certain day, go to the
days by using
and . The current active prole
status prole will display.
Different ECO proles may be applied to the
thermostat for any day of the week.
If one ECO prole is used in most rooms:
Apply the prole to every room. In step 3, select
the setting All. Then set individual rooms.
Setting Time and Date
1. Uponor screen > Main Menu > Settings > System
Parameters
> Clock Settings > Set Date/Time
Toggle between the elds using the
and
keys. Change the values using the
and
keys.
2. Change the time and date.
> Press OK.
Setting the Time Format
1. Uponor screen
> Main Menu > Settings > System
Parameters
> Clock Settings > Time Format
2. 24 hour or AM/PM
> Press OK.
Setting the Date Format
1. Uponor screen
> Main Menu >
Settings
> System Parameters >
Clock Settings
> Date Format
2. Select the format.
> Press OK.
ECO All
ECO Night&Day
ECO Off
ECO Profiles List
00:00 ECO
ECO Night&Day - Heat
39.2˚F
ECO
Settings Menu
The settings menu allows the user to set the base unit for
individual rooms.
The number at the beginning of the room
name on the display means:
First digit: base unit number (1, 2, 3); second
and third digits: number of the rst channel
controlled by this thermostat (01, 02, 03, ...).
(If several channels are controlled by the same
thermostat, only the lowest terminal number
is displayed.)
Assigning or Changing a Room Name
1. Uponor screen > Main Menu > Settings > Rooms
> Room Names
2. Select the desired controller (only
applies if more than one controller
is installed) > Press OK.
3. Select the desired room or
thermostat. > Press OK.
4. Select the room name from the
predened list. > Press OK.
Setting the Min and Max Temperatures
1. Uponor screen > Main Menu > Settings > Rooms >
Min / Max Temperatures
2. Select the desired base unit or All
for all rooms on all base units >
Press OK.
Selecting All sets the same min and max
temperatures for all rooms.
3. Select the desired thermostat or
room.
> Press OK.
4. Set the temperatures
Use
and to increase and
decrease the value.
Use
and to toggle between
min. and max.
> Press OK.
Example: If the temperature setpoint of the
thermostat is set to 41°F, the temperature will
not fall below 53.6°F because the minimum
and maximum limitations for this room are set
to 53.6°F and 78.8°F respectively.
Information Menu: System Information
Heating Mode
Uponor screen
> Main Menu > Information > System >
Operating Mode
Operating Mode
The system is always in heat mode.
Access Level
Uponor screen
> Main Menu > Information > System
> Access level
Displays the current access level.
Software Version
Uponor screen
> Main Menu > Information > System
> Software Version
Software Version
Hardware Version
ECO Mode
Reset proles to the default values by
re-editing. In heat mode, ECO mode reduces
room temperatures at the set times. There are
ve different time and temperature proles
available, and all can be modied.
Steps to Follow
1. Edit the ECO proles.
2. Apply the ECO proles.
ECO Prole
This system provides ve periods for
temperature reduction settings, which indicate
each setting, but are fully programmable.
Set the timers rst. Then dene which
thermostat each timer is to control.
Heating
ECO Off
ECO All
X.X.X
Interface : 1.0.16 (1.0.2)
#1 Base Unit : 1.0.17 (1.0.3)
#2 Base Unit : 1.0.17 (1.0.3)
Software Version
Mode
Heat.
Operating Mode
OK
Basic
Access Level
(X.X.X.)
�
Base Unit List
Controller 1
Controller 1
All
Base Unit List
1.07 Gym
1.02 Living
Room List
1.07 Gym
1.02 Living
Room List
Master BD
Dining
Living
Default Room Names
Max
500˚F
Min/Max temperatures
Min
248˚F
14 Jan 2008
2 : 02
Set Date/Time
Please choose the
required time format.
24 hour
AM / PM
Time Format
YYYY / MM / DD
DD Mmm YYYY
DD / MM / YYYY
Date Format
Controller 1
All
Base Unit List
All
1.02 Living
1.07 Gym
Room List
MonTueWedThuFriSatSun
ECO Off
System
MonTueWedThuFriSatSun
ECO Custom
1.02 Living
ECO All
ECO Night&Day
ECO Off
ECO Profiles List